Here are some pics of my bravada. Installed the wheels and system on saturday

http://i463.photobucket.com/albums/qq351/kegraffix/brav6.jpg

http://i463.photobucket.com/albums/qq351/kegraffix/brav3.jpg

http://i463.photobucket.com/albums/qq351/kegraffix/brav4.jpg

Front windows will be tinted in the next week or so


Pic of the amp setup:
http://i463.photobucket.com/albums/qq351/kegraffix/amp.jpg

This is what I have in the truck:
- Kenwood eXcelon KDC X991 Radio w/Ipod dock in the glove box
- JL Audio TR650-CXI's in the doors
- JL Audio TR400-CXI in the dash
- 2-10" JL Audio w3v3's
- JL Audio Slash 500/1 mono amp
- JL Audio Slash 300/4 for speakers
- 2 farad cap

I'm currently working on a custom box that will be wrapped in leather with a wood grain insert to match the interior. It will go from one end to the other.

Here's A sketch
http://i463.photobucket.com/albums/qq351/kegraffix/box.jpg
And a setup that looks pritty close to what I am doing minus the amps.
http://i463.photobucket.com/albums/qq351/kegraffix/sub.jpg

I will post pics when its done. maybe by next weekend.

Very nice!

Do you think this would be better in the "Builds" section? Just asking.

Very nice! I've seen a few bravada's around where I live but they're '92 or '93 models I believe.

Very nice!

Do you think this would be better in the "Builds" section? Just asking.

Im just going to post a pic of the box finished and installed, but if you think thats where it should go that's cool with me.

Thanks for the comment and nice Buick

It was just a suggestion. If you do more work to it, you can keep this thread updated.

Great, Thanks

Update on box. the Leather I ordered is on back order so I wont be getting that in till next week. So as soon as I finish with it I will post some pics.

Thats a nice bravada, got to test drive one of those back a couple years ago and the options were very cool

Well It took a little longer then I thought, but the enclosure is finally done. I ended up going with a gloss black acrylic insert instead of the wood grain. Couldnt find a wood grain vinyl that would match right. So what you guys think?

http://i463.photobucket.com/albums/qq351/kegraffix/IMG_0805.jpg
http://i463.photobucket.com/albums/qq351/kegraffix/IMG_0806.jpg
http://i463.photobucket.com/albums/qq351/kegraffix/IMG_0807.jpg

Looks like excellent work!

that is one clean bravada, and great work on the box.

good job on the box, it looks very clean. it's a lot nicer than one of those "off the shelf" things. how does it sound?

Just got a pair of european blazer tails. still figuring out how to wire them up to work how they should.

http://i463.photobucket.com/albums/qq351/kegraffix/IMG_0851.jpg

http://i463.photobucket.com/albums/qq351/kegraffix/IMG_0852.jpg

They look nice!

You may have some difficulty getting them to work though. The brake lights and turn signals are one in the same on the US spec blazers.

Nice lights, post what you find on the hook up, I have a set coming in this week and never gave it a thought about the same issue your looking at.

They look nice!

You may have some difficulty getting them to work though. The brake lights and turn signals are one in the same on the US spec blazers.

I took a look at the wiring and from what it shows in the schmatics the wire that controls the turn signals for the rear are controled from two wires (yellow wire drivers side and Dark Green for passenger side) That start at the turn signal switch all they way to the rear lights. It also looks like the brake lights are wired apart from the turn signal (Brown Wire). It looks like they both just tie in at the bulb. So what im going to try and do is cut the turn signal wire which is the yellow wire on each side and see if it disables them but still allows the brake/park lights to work. If it does work then I can just wire the fourth bulb for the turn signal there. I read on s10forum about someone doing this for the s10 euro tails.