what have you gotten done on your blazer today?
#801
02-17-2010, 05:45 PM
well... I did the fishing line to remove the badge. It's when I went to scrape the tape off with a plastic putty knife. I went too aggressive. But a heat gun will make tape removal easier. Hopefully.
#803
02-17-2010, 06:57 PM
Originally Posted by cbr995
well... I did the fishing line to remove the badge. It's when I went to scrape the tape off with a plastic putty knife. I went too aggressive. But a heat gun will make tape removal easier. Hopefully.
#804
02-17-2010, 08:03 PM
Originally Posted by ABN31B
Ouch...
nothing a little buff and polish can't handle....
Post up some pics in the paint section. Maybe somebody can point out a decent clay bar/wax/polishing compound to help you out some
Originally Posted by stsrus
I used mineral spirits and my thumb nails, A little hard on the manicure but didn't scratch the paint
Last edited by cbr995; 02-17-2010 at 08:06 PM.
#805
02-17-2010, 10:26 PM
Originally Posted by ABN31B
The mounts i was going to use for my off-road lights would have required drilling.... and I plan to toss a 17' canoe up there, so strength will matter. SO, I got new mounts that bolt on. #2 conduit clamps from Home Depot. $.068 each.
with a little bit of under coating, they should do nicely... (flip them over in your mind).
with a little bit of under coating, they should do nicely... (flip them over in your mind).
Originally Posted by wlorton
WHEW!.... the ones like mine are so sexy... never get rid of them if you got em...
'cause there are alot of them around here, but they're all chedder, and that's why i'm gonna be sportin' the old skool (refreshed) rims for the Summer time.
i'm talkin' about these ones,
Originally Posted by zedartwo
I'm 10 minutes straight up the highway. I would helped but Ole' Jim is being a wuss. Engine light keeps going on and off.
Gotta get'er checked out.
Gotta get'er checked out.
Matt, that just plain sucks about your efforts to debadge. maybe you can get the guys @ the body shop to clean it up, when they fix your end cap fiasco.
#806
02-17-2010, 10:30 PM
Originally Posted by old skool luvr
yeah, i know (general area anyways). i coulda brought my scan tool too if you came.
#807
02-17-2010, 10:42 PM
The Westin safari bar that my wife ordered for me came in today while I was at school. Couldn't wait, so I went to my brother's house after church, used his garage, and put it on. I think it was well worth the effort, plus I'll be able to sport the new look tomorrow when I go back to school.
Last edited by jdespain; 02-17-2010 at 11:28 PM.
#808
02-17-2010, 11:06 PM
Originally Posted by zedartwo
Well i got it read and its the pass o2 sensor. Hard change?
nope. especially with the extra ground clearance you have.
just find a nice dry spot to lay down on. although that might be kinda hard, with the little bit of wet stuff we've been getting the last few days.
#809
02-17-2010, 11:07 PM
i removed everthing in the engine compartment so that i can pull my engine? getting ready to rebuild the motor or buy a new one havnt decided yet. then after its running im gonna move to the inside.
#810
02-17-2010, 11:32 PM
Originally Posted by K5corey
i removed everthing in the engine compartment so that i can pull my engine? getting ready to rebuild the motor or buy a new one havnt decided yet. then after its running im gonna move to the inside.
