Blazer Forum - Chevy Blazer Forums - Search Results

 
Search: Posts Made By: j89lumaye
Showing results 1 to 50 of 144
Search took 0.01 seconds.
12-01-2013, 04:12 PM
Replies: 1
Views: 560
Posted By j89lumaye

What are these?

I took these rims in on trade for a truck I had and idk what they are
They have American racing center caps but I cant find them through summit or American racing or anything else.
Anybody have any...
07-31-2012, 01:52 PM
Replies: 3
Views: 1,372
Posted By j89lumaye

that we didnt do, and im not sure on the delco...

that we didnt do, and im not sure on the delco part because they asked after it was done
Dont you just unhook the battery to reset the pcm?
07-28-2012, 12:56 PM
Replies: 3
Views: 1,372
Posted By j89lumaye

Low voltage in o2 sensors on a 97 gmc

One of my friends went and replaced all 4 o2 sensors on his truck, and now hes got all 4 codes popping up
All the connections are fine, and we tested the voltage at the connector and it was fine
I...
Forum: Lifting Tech
04-16-2012, 04:29 PM
Replies: 9
Views: 3,283
Posted By j89lumaye

I would go with the Rough country 2.5" lift, and...

I would go with the Rough country 2.5" lift, and 31s
the lift is more expensive then the body lift, but you know the 31s will clear then
Forum: The Lounge
03-30-2012, 01:06 AM
Replies: 27
Views: 1,668
Posted By j89lumaye

My grandpa broke a transfer case off the tranny...

My grandpa broke a transfer case off the tranny just like that
Cause: Hit a tree with front axle, bending the front dana 60, pushing/bending driveshaft, breaking the t case off the tranny, bending...
Forum: General Chat
03-26-2012, 10:57 PM
Replies: 15
Views: 1,820
Posted By j89lumaye

I dont think so I think it was a 80s camaro...

I dont think so
I think it was a 80s camaro with T-tops that was a donor to that blazer
Forum: Builds
03-26-2012, 09:47 PM
Replies: 47
Views: 14,479
Posted By j89lumaye

Cavalier/sunfire seats bolt right into your rails...

Cavalier/sunfire seats bolt right into your rails or frame
I think 4th gen camaro seats do too
Forum: Builds
03-26-2012, 01:59 PM
Replies: 2
Views: 714
Posted By j89lumaye

Pick n pulls, junk yards, and you can try...

Pick n pulls, junk yards, and you can try craigslist or ebay. I know a couple junk yards here have them
03-18-2012, 01:39 AM
Replies: 26
Views: 6,077
Posted By j89lumaye

1/2 inch threaded rod and some big washers welded...

1/2 inch threaded rod and some big washers welded to some 1/2 washers is what i did when i put shackles in my blazer
Forum: Off Roading
03-14-2012, 10:36 PM
Replies: 4
Views: 1,072
Posted By j89lumaye

Friends swampy mud pit=bad ideas

I have no pictures of the tractors being stuck, but we buried a john deere 4020 instantly before we started playin with trucks or the grizzly
Then we decide to get his other john deere 6030 (i think...
Forum: General Chat
03-13-2012, 08:12 PM
Replies: 7
Views: 2,435
Posted By j89lumaye

If it was the bearing, all the $hit that coulda...

If it was the bearing, all the $hit that coulda got into it by the looks of that engine bay doesnt make it much better then what it coulda been
03-12-2012, 10:04 PM
Replies: 5
Views: 1,027
Posted By j89lumaye

Swap it out for a 3.4 first, then think about cams

Swap it out for a 3.4 first, then think about cams
03-12-2012, 09:55 PM
Replies: 8
Views: 10,083
Posted By j89lumaye

2HI -> 4HI-any speed up to 35 pretty much 2HI...

2HI -> 4HI-any speed up to 35 pretty much
2HI -> 4LO-Stopped or under 2-3 mph
4HI -> 4LO- Stopped or under 2-3 mph
4HI -> 2HI- any speed up to 35 pretty much
4LO -> 2HI- Stopped or under 2-3mph...
03-12-2012, 09:42 PM
Replies: 6
Views: 1,133
Posted By j89lumaye

Sand it to get a rough surface, then i do 2 coats...

Sand it to get a rough surface, then i do 2 coats primer, 2 coats color, and clear if you want to
Forum: General Chat
03-10-2012, 01:32 AM
Replies: 90
Views: 42,088
Posted By j89lumaye

I flat towed a 02 chrysler town and country for...

I flat towed a 02 chrysler town and country for about 20 miles to the shop with my 96 blazer 4x4, stock size tires, and 3.42s, she begged on hills, but the tranny was also goin out on that thing
03-06-2012, 08:37 PM
Replies: 13
Views: 1,483
Posted By j89lumaye

Bending 1/4-pain in the ass with 3 people, a...

Bending 1/4-pain in the ass with 3 people, a welder to tack, and a bench vise
Welding gaps after using acetylene torch-pain in the ass as well
New bumper with a few bends to match the front...
03-04-2012, 01:50 AM
Replies: 2
Views: 1,260
Posted By j89lumaye

Just bleed it out, it only takes 5 min with 2...

Just bleed it out, it only takes 5 min with 2 people
03-04-2012, 01:19 AM
Replies: 8
Views: 2,351
Posted By j89lumaye

maybe if you would put some roundness on the...

maybe if you would put some roundness on the edges of the fenders and on the front of the hood it would look decent. Raisng the front of the hood isnt a bad idea, i always hated my blazer dint feel...
Forum: The Lounge
03-04-2012, 12:49 AM
Replies: 7
Views: 1,181
Posted By j89lumaye

Thanks guys, that 60degreev6 looks really handy...

Thanks guys, that 60degreev6 looks really handy if youd rebuild one of em for sure
Forum: The Lounge
02-29-2012, 11:22 PM
Replies: 7
Views: 1,181
Posted By j89lumaye

Swapping some wiring stuff wouldnt be too big of...

Swapping some wiring stuff wouldnt be too big of a deal as long as they mount the same way too. What i wanna do is find another lumina either on the road or a junk yard and look at everything to see...
Forum: The Lounge
02-29-2012, 12:40 PM
Replies: 7
Views: 1,181
Posted By j89lumaye

I know they all do, one kid at school has one...

I know they all do, one kid at school has one that has had a rod knock for 40k miles and he still drives it everyday. But if it goes im thinkin about swapping the 3.4 in
Forum: The Lounge
02-28-2012, 10:31 PM
Replies: 7
Views: 1,181
Posted By j89lumaye

3.1 to 3.4 swap

Would a computer be needed to swap a 3.4 into a car with a 3.1?
What would be needed if not?
I bought a 94 lumina with the flat top 3.1, shes got a knock when its cold, but within a block it goes...
Forum: Lifting Tech
02-27-2012, 10:46 PM
Replies: 3
Views: 575
Posted By j89lumaye

I just put a bottle jack in between the frame and...

I just put a bottle jack in between the frame and spring and used it to push them down until i had the holes lined up
Forum: General Chat
02-24-2012, 07:17 AM
Replies: 14
Views: 1,344
Posted By j89lumaye

I miss the 4x4 and feeling of being able to go...

I miss the 4x4 and feeling of being able to go anywhere or take a ditch when i feel like it lol
But i dont miss my tranny slipping, or 11 mpg
Forum: General Chat
02-23-2012, 03:53 PM
Replies: 14
Views: 1,344
Posted By j89lumaye

Well heres pics of the car, shes a good deal with...

Well heres pics of the car, shes a good deal with 124k and $1350 (click to make em bigger)
http://i470.photobucket.com/albums/rr64/j89lumaye/th_lumina3.jpg...
Forum: Builds
02-21-2012, 09:20 PM
Replies: 205
Views: 33,688
Posted By j89lumaye

Im pretty sure they are the 93-02 body style...

Im pretty sure they are the 93-02 body style camaro wheels
Forum: General Chat
02-21-2012, 08:43 PM
Replies: 1
Views: 619
Posted By j89lumaye

pretty sure a explorer doesnt have locking hubs...

pretty sure a explorer doesnt have locking hubs but im not sure on its engagement. I know the 94+ dodges have a vacuum engagement front axle (well for 1 tons at least) but im not sure, any older ford...
02-21-2012, 08:20 PM
Replies: 7
Views: 3,405
Posted By j89lumaye

Power to switches-i would run from battery with a...

Power to switches-i would run from battery with a fuse in it
Gettin wires into interior-driver side fender has a small gap big enough for an amp wire plus i had 6 other wires. You can run it in thru...
Forum: Builds
02-21-2012, 07:49 PM
Replies: 126
Views: 25,230
Posted By j89lumaye

Sounds good, i just sold the blazer this past...

Sounds good, i just sold the blazer this past weekend for a 94 lumina coupe and im not thinkin about puttin that on there lol
Forum: General Chat
02-21-2012, 07:16 PM
Replies: 1
Views: 1,643
Posted By j89lumaye

id just go get a 5 inch kit and not risk crankin...

id just go get a 5 inch kit and not risk crankin t bars and wearin front end parts out like crazy
Forum: General Chat
02-20-2012, 07:55 PM
Replies: 14
Views: 1,344
Posted By j89lumaye

repost

repost
Forum: General Chat
02-20-2012, 07:50 PM
Replies: 14
Views: 1,344
Posted By j89lumaye

I laughed too But he is DEAD SERIOUS about hot...

I laughed too But he is DEAD SERIOUS about hot roddin a minivan lol. I plan on helpin if hes gonna do it tho. Right now he works in a body shop and his grandpa has all the tools to do it in his shop,...
Forum: Builds
02-20-2012, 07:45 PM
Replies: 126
Views: 25,230
Posted By j89lumaye

Before you mount your bull bar you should buy my...

Before you mount your bull bar you should buy my bumper, im only gonna ask 75 bucks, and its HEAVY DUTY. 1/4 inch C channel with the bottom 4 inches cut off so its about 6 inches tall. It would need...
Forum: General Chat
02-20-2012, 07:30 PM
Replies: 14
Views: 1,344
Posted By j89lumaye

Shes got a little rust for on the drivers side...

Shes got a little rust for on the drivers side but my uncle might have a car with a donor wheel well
And thats the first thing i did, we had one 3.1 in the family in a 97 grand am
3 sets of warped...
Forum: General Chat
02-20-2012, 07:26 PM
Replies: 14
Views: 1,344
Posted By j89lumaye

Your gonna love this, my friend is lookin at a...

Your gonna love this, my friend is lookin at a lumina APV (yes the van)
He wants to put a 355 and slicks with a 9" rear end and 4:10s with like 28x10s
That thing will be ungodly fast for a minivan
Forum: General Chat
02-20-2012, 07:22 PM
Replies: 14
Views: 1,344
Posted By j89lumaye

I kinda wanna get some 17s since i got 15s, maybe...

I kinda wanna get some 17s since i got 15s, maybe a little lower if it dont look right
But i will NOT turn this into a mexican mobile

EDIT: Oh man im gettin these guys...
Forum: General Chat
02-20-2012, 07:15 PM
Replies: 14
Views: 1,344
Posted By j89lumaye

Well, nobody with a bonneville could let me see...

Well, nobody with a bonneville could let me see the car today, so i "settled" for a 94 Lumina Euro with a 3.1 v6. Guy was askin 1500 and got it for 1350, 1500 with registration
At least i got a...
Forum: General Chat
02-20-2012, 12:05 AM
Replies: 14
Views: 1,344
Posted By j89lumaye

No more Blazer

I am no longer a blazer owner, i sold it saturday, feb 19th for 1500 bucks with rust and a smashed side and a tranny thats close to goin
Im lookin at a couple late 90's bonnevilles now
I had a 92...
Forum: Lifting Tech
02-19-2012, 11:57 PM
Replies: 9
Views: 4,647
Posted By j89lumaye

We dont have springs in a 4x4, just torsion bars...

We dont have springs in a 4x4, just torsion bars and shocks
02-17-2012, 10:54 PM
Replies: 8
Views: 828
Posted By j89lumaye

i did check all the fuses in there, and that was...

i did check all the fuses in there, and that was one that i left in there. Only ones i didnt were Air Bag and DRL's, but i will check that one again and put other fuses in it
02-17-2012, 07:07 PM
Replies: 8
Views: 828
Posted By j89lumaye

they are but none come up as a dome, horn, or...

they are but none come up as a dome, horn, or rear hatch. The rear hatch fuse should be under the hood. But i cant find any under the hood
02-17-2012, 07:05 PM
Replies: 3
Views: 1,194
Posted By j89lumaye

i cant find any fuse boxes under the hood, the...

i cant find any fuse boxes under the hood, the a/c compressor, computer, and battery are on the left, somethin gray and the cruise control on the other side?
02-17-2012, 05:36 PM
Replies: 3
Views: 1,194
Posted By j89lumaye

Rear Hatch glass

The hatch doesnt make the noise to open it, horn and dome light all died out one night
Im thinkin its a fuse, but i dont have the under hood fuses, or cant find them at least, and i checked every...
02-15-2012, 10:12 PM
Replies: 2
Views: 4,741
Posted By j89lumaye

my 96 4x4 should have 235/70s but i put 235/75s...

my 96 4x4 should have 235/70s but i put 235/75s on it and my speedo is minimally off. My speedo and 3 different gps's only say its 1 off and its hardly ever that i saw it be different between the two
Forum: Builds
02-12-2012, 11:37 AM
Replies: 126
Views: 25,230
Posted By j89lumaye

I wouldnt go for it. You should get a black one...

I wouldnt go for it. You should get a black one anyway. Tan+chrome dont mix in my opinion
Forum: Builds
02-11-2012, 04:47 PM
Replies: 9
Views: 2,115
Posted By j89lumaye

Take a floor jack, put it in neutral, pick up the...

Take a floor jack, put it in neutral, pick up the front tires and drag the whole thing over so that it turns
Forum: Off Roading
02-07-2012, 07:47 PM
Replies: 35
Views: 15,023
Posted By j89lumaye

ive had 2 4 doors so far, one first and one...

ive had 2 4 doors so far, one first and one second gen
with my with my goodyear wrangler mt/r's on the 96, i go thru some **** like its dry pavement
with my bfg a/t's on my 92, i would spin more,...
Forum: Lifting Tech
02-07-2012, 06:53 PM
Replies: 13
Views: 1,672
Posted By j89lumaye

You got it all wrong here You put in the diff...

You got it all wrong here
You put in the diff drop brackets so you dont have to crank the t bars up
So say you buy the RC 2.5 lift kit. You get 2 inch shackles in back, then 2.5 up front. You can...
02-06-2012, 10:02 PM
Replies: 1
Views: 624
Posted By j89lumaye

Im thinkin so. My fender looks to be the same as...

Im thinkin so. My fender looks to be the same as yours. But mines a 4 door blazer, my grill looks to fill the edge of your headlight does. I would go with it. Just ask if you could test fit if...
02-06-2012, 09:38 PM
Replies: 12
Views: 2,336
Posted By j89lumaye

treadwright.com ^cheap tires, mud or all...

treadwright.com
^cheap tires, mud or all terrains. i figured it out, you pay less for 4 tires and shipping then you do for the 4 plus shipping from tire rack
Yes, they might be retreads, but ive...
Showing results 1 to 50 of 144
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.