Blazer Forum - Chevy Blazer Forums - Search Results

 
Search: Posts Made By: 20Blazer00
Showing results 1 to 50 of 500
Search took 0.04 seconds.
12-27-2008, 09:27 PM
Replies: 19
Views: 3,117
Posted By 20Blazer00

RE: Engine Advance Question

Try checking your EGR valve on the front of the intake manifold. It is the coke can like device with wires coming out of it by the thermostat housing. If you remove this you can see the Pintle that...
11-08-2007, 01:08 AM
Replies: 8
Views: 1,044
Posted By 20Blazer00

RE: Time Lag Drive-Reverse

Depending on the condition of the fluid you might just need a fluid and filter change. How many miles on the Blazer and has it had any tranny maintainance??
11-08-2007, 01:05 AM
Replies: 6
Views: 1,891
Posted By 20Blazer00

RE: 99 Blazer/no start/will start.....?

GM had a TSB about moisture build up in the distributor because of clogged screens at the base of the distributor housing...they recomended punching out the screens and drying it out...but you should...
11-08-2007, 12:55 AM
Replies: 21
Views: 7,795
Posted By 20Blazer00

RE: '95-97 Grille Removal and Headlight Installation (Sealed Beam)

I am a little puzzled as to why you had to cut your headlight connectors for the H4 conversion. The H4 conversions are supposed to be a direct replacement without the need to cut/adapt connectors, at...
11-08-2007, 12:30 AM
Replies: 3
Views: 679
Posted By 20Blazer00

RE: Fuel pump questions..

Failing sending unit does not mean the pump will fail except if you run it dry to many times....the fuel pump needs at least 1/4 tank to be completely covered in cold fuel to keep its internal temps...
10-30-2007, 12:04 AM
Replies: 3
Views: 2,401
Posted By 20Blazer00

RE: Coolant change DIY?

Well if you want to do a full system flush then you should purchase a chemical flush product, from Prestone. You run it for a little while according to the directions. Then drain your coolant into an...
10-02-2007, 02:59 PM
Replies: 2
Views: 701
Posted By 20Blazer00

RE: Plugs and wires and a suspension question.

I am sure that the plugs and wires would work on a '96 but the style of plug makes a difference, ie bosch + series plugs should be avoided since there have been threads complain about misfires with...
10-02-2007, 02:40 PM
Replies: 37
Views: 3,146
Posted By 20Blazer00

RE: 100-130 miles to a TANK!

rriddle3 is correct about the BBB it is not an enforcement agency of the Government. I filed a complaint with the BBB a couple years ago about a shop that had rebuilt the engine and tranny of my '86...
10-02-2007, 01:59 PM
Replies: 37
Views: 3,146
Posted By 20Blazer00

RE: 100-130 miles to a TANK!

Well gas mileage is more of a product of many things. One the burn rate of the fuel you use for powering your vehicle, ie: ARCO uses a blend of ethanol and gasoline which reduces emissions, it also...
10-02-2007, 01:11 AM
Replies: 37
Views: 3,146
Posted By 20Blazer00

RE: 100-130 miles to a TANK!

I agree with Kyle take it back to Autozone and make sure that they give you the correct pump for your engine and year...and have them show you the part number in their catalogue. Also before you go...
08-02-2007, 02:22 PM
Replies: 8
Views: 8,914
Posted By 20Blazer00

RE: noise like jet engine, help?

BlueBlazer2001:

If you want to check belt noise then remove the belt for a short time and see if the sound is still there; do this when the engine is cold or barely warm since not turning the...
07-21-2007, 04:29 PM
Replies: 4
Views: 2,090
Posted By 20Blazer00

RE: Radiator cap

The stock radiator is rated to 18lbs....plus thehigher thepressure thehigher the boiling point of the fluid in the radiator...I have a friend that is using a 22lb camaro cap on his 96 GMC Sonoma...
07-21-2007, 04:16 PM
Replies: 7
Views: 27,331
Posted By 20Blazer00

RE: Clutch Fan Hell

Also the thread for the clutch fan mounting nut is a left hand thread....
07-18-2007, 01:52 AM
Replies: 9
Views: 4,165
Posted By 20Blazer00

RE: Metallic clicking while accelerating

To isolate the noise you might try unbolting the front driveline from the trans axle...if the noise persists then you know that it will be internal components from the transfer case...one wild guess...
07-13-2007, 10:18 AM
Replies: 3
Views: 1,589
Posted By 20Blazer00

RE: when turnin steering wheel alot to one side makes a popin noise what is it?

I had this problem last year with popping noise when backing out of driveway with wheel turned. I did like Kyle explained and found the drivers side lower ball joint was excessively worn and so I...
07-11-2007, 09:09 PM
Replies: 4
Views: 652
Posted By 20Blazer00

RE: leak near fromt end

gear oil not clear...and has nasty smell...
07-11-2007, 09:08 PM
Replies: 10
Views: 2,757
Posted By 20Blazer00

RE: Blazer looses power, chokes, then shuts down when over 85 deg outside

Does this fuel pump have a pulsator valve???? If so it sounds like it is failing .... I have read threads where this was the case and all they had to do was to replace that part with a length of fuel...
07-11-2007, 09:01 PM
Replies: 17
Views: 6,133
Posted By 20Blazer00

RE: Strange No start condition after a hard rain!

Check the base of the distributor for clogged vents....on the under side of the distributor there are supposed to be 2 vents to allow moisture out...these get clogged with debris and cause a moisture...
07-06-2007, 02:04 AM
Replies: 2
Views: 809
Posted By 20Blazer00

RE: '98 blazer sometimes rolls forward while in reverse

Sounds like you need a tranny filter and maybe a flush...also have the computer scanned for codes to see if there might be some other thing to look into. It might be possible that an internal...
07-06-2007, 02:00 AM
Replies: 13
Views: 2,065
Posted By 20Blazer00

RE: Of course...4x4 Problem

dmxmessenger,

If the Dealer is a GM Dealer then I would think twice about them working on my truck... If they can't figure out the part and location...do a search for TCCM and...
07-06-2007, 01:49 AM
Replies: 1
Views: 1,002
Posted By 20Blazer00

RE: Sway. vibration and creak

The first thing to check is the front swaybar end links. They have small rubber parts that if worn out will not let the anti-sway bar function properly...in the photo you will see the rubber bushings...
07-05-2007, 02:02 AM
Replies: 1
Views: 740
Posted By 20Blazer00

RE: Broken return spring?

On chevrolet starters the solenoid has a internal coil wound spring to release the starter gear away from the flywheel, should the spring fail then the gear could hit the flywheel and cause damage to...
07-05-2007, 01:50 AM
Replies: 3
Views: 1,005
Posted By 20Blazer00

RE: 2005 blazer senior rough idle.

Check for all possible vacuum leaks. Your Evap purge solenoid is located on the intake manifold and if it or the MAP sensor went bad they either or both can cause a leak. Also make sure all tune up...
07-03-2007, 12:35 PM
Replies: 4
Views: 4,560
Posted By 20Blazer00

RE: 98 Blazer shifter dash light not working.

I remember looking this up and I believe that there is a bulletin for this situation but the service information CD I got from E-bay all of a sudden quit working after security updates from...
07-03-2007, 12:31 PM
Replies: 3
Views: 9,982
Posted By 20Blazer00

RE: Gas pedal height or throttle cable adjustment?

Before taking out the assy check the other gas pedals of some other Blazers at local lots. Make sure that someone did not bend the pedal arm or that the cable is not stretched. Another possibility is...
06-24-2007, 01:04 PM
Replies: 13
Views: 11,564
Posted By 20Blazer00

RE: 2002 Blazer won't start. Fuel Pump?

There is a pressure sensor on the fuel pump housing for the Evap system...it could be bad....or when you replaced the pump the seal is not correctly fitted to the tank..... or there is a small crack...
06-22-2007, 05:37 PM
Replies: 2
Views: 638
Posted By 20Blazer00

RE: What model Blazer do I have?

The easiest way to get information on your Blazer is to get the VIN# and call any GM Service Department and tell them your situation and they can either tell you over the phone or you can go to the...
06-19-2007, 01:21 PM
Replies: 12
Views: 1,200
Posted By 20Blazer00

RE: wheel hub

You maybe right and not need wheel bearings, you could have CV joints going bad...raise up the front end onto jack stands and start poking around to see what has excessive movement...ball joints are...
06-19-2007, 01:10 PM
Replies: 10
Views: 1,787
Posted By 20Blazer00

RE: STUCK THROTTLE? TRANNY ACTING FUNNY AT HIGHER SPEEDS?

Has anybody considered an out of adjustment kick down cable if the model year and tranny fit???
06-19-2007, 12:30 AM
Replies: 31
Views: 4,760
Posted By 20Blazer00

RE: biggest engine in a 2000 4 door

You can put in "any" SMALL BLOCK CHEVY engine depending on how you want to use it after the swap I would recomend the 383 stroker!!!
06-16-2007, 01:09 PM
Replies: 3
Views: 5,909
Posted By 20Blazer00

RE: gas tank capacity

GM fuel sending units are notoriously inaccurate. If you have seen them on E-bay you would see why. They work like an old toilet tank float, hinged at a fixed point with electric contacs to determine...
06-16-2007, 12:47 PM
Replies: 8
Views: 887
Posted By 20Blazer00

RE: Just got my DMV renewal notice...

If the leak is big enough then you would definitely smell hot coolant.
The check engine light might not come on depending on how many times the drive cycle has been completed. Some DTC's never set...
06-15-2007, 05:54 PM
Replies: 12
Views: 1,200
Posted By 20Blazer00

RE: wheel hub

Find out from the shop how they tighten down the nut...ask them for the torque value for the axle nut and then get your self a 1/2" torque wrench and double check their work that way you can be sure...
06-15-2007, 05:47 PM
Replies: 8
Views: 887
Posted By 20Blazer00

RE: Just got my DMV renewal notice...

Your heater core can only affect the smog test if it is leaking coolant like a broken dam, and won't allow the engine to reach closed loop mode in the programed time and sets a DTC code...
06-14-2007, 08:35 PM
Replies: 7
Views: 678
Posted By 20Blazer00

RE: Proper Pivots -HELP

Kyle he maybe looking for parts to the "Export Version" of the blazer...the GM Service DVD makes mention of them but, My DvD quit working with all the latest "security updates" and MS Genuine...
06-13-2007, 12:58 PM
Replies: 5
Views: 2,398
Posted By 20Blazer00

RE: Multifunction switch

There is a major ground on the radiator support under/near the battery box. There are also smaller grounds from the engine to firewall and near most headlight/taillight locations..also check the...
06-13-2007, 01:34 AM
Replies: 3
Views: 1,027
Posted By 20Blazer00

RE: Feels like it's missing while idleing?......

Start by scanning the computer for codes...then start looking for a vaccuum leak, could be a hose or could be a loose part on the intake, or could be any vacuum sensor in the engine compartment...
...
06-09-2007, 06:29 PM
Replies: 4
Views: 698
Posted By 20Blazer00

RE: Grrr...fuel pump

Check with your local auto parts store for a special tool, but usually you will need to just squeeze the fitting and pull apart the fitting...to figure out how try the fuel filter, it has one of this...
06-09-2007, 06:25 PM
Replies: 6
Views: 939
Posted By 20Blazer00

RE: Coolant Leak?

I would check the intake manifold gaskets for leaks at the base of the intake, generally if they leak it can be obvious at the edges of the intake at the front and rear of the heads in the "valley...
06-09-2007, 05:41 PM
Replies: 8
Views: 1,411
Posted By 20Blazer00

RE: Removing Front Rotors

Hill Billy,

Since this is a 2wd not a 4wd the front hubs are not the same. I noticed when I looked at the GM Service DVD (not working now) that the 2wd bearings were replaceable as seperate...
06-08-2007, 11:30 PM
Replies: 3
Views: 1,081
Posted By 20Blazer00

RE: 99 Jimmy hesitation

I would check alternator my 2000 puts out 13.8v-14.1v at idle to 3000rpm and more...the internalvoltage regulator in the alternator might be shot. When A/C is on then more like 13.8v. but if you are...
06-08-2007, 11:11 PM
Replies: 13
Views: 11,564
Posted By 20Blazer00

RE: 2002 Blazer won't start. Fuel Pump?

I can't remember where the fuel pump relay is physically located but there are multiple relays next to each other...I think on the firewall passenger side(????), switch one of those around making...
06-08-2007, 11:01 PM
Replies: 12
Views: 1,013
Posted By 20Blazer00

RE: wiring prob with the POS

I would be my bet that what ever wire got melted by the manifold it is that circuit that is causing the trouble. I would check the wire for continuity/resistance, if the wires got hot enough from the...
06-08-2007, 10:53 PM
Replies: 4
Views: 855
Posted By 20Blazer00

RE: Need help electrical issue

I would start with a continuity check (ohms/resistance) to see if there is a short in the wire or excessive resistance. As far as the voltage I am only guessing that it should range from 0v-3.3v or...
06-08-2007, 02:26 AM
Replies: 4
Views: 855
Posted By 20Blazer00

RE: Need help electrical issue

Do you have an oiled foam filter ie: K&N style. If you recently cleaned and reapplied oil onto the filter any excess oil might be fouling the MAF sensor wires, it is a known condition with these...
06-08-2007, 02:14 AM
Replies: 7
Views: 3,859
Posted By 20Blazer00

RE: Removing 3rd Spark plug and Steering Shaft??

If the original plug was "stripped" when you removed it then the previous install would have been what stripped the threads, you can not strip a thread by removing it, only when you install something...
06-02-2007, 11:22 PM
Replies: 4
Views: 2,680
Posted By 20Blazer00

RE: 98 4.3 4wd Blazer engine running rough

Is it still running rough??? It is also possible that a plug wire may have worked loose...I have read on the forum that the crab cap distributor cap can "push" the wire boot backwards enough to cause...
06-02-2007, 11:10 PM
Replies: 6
Views: 905
Posted By 20Blazer00

RE: 99 4.3L wont start

He could try but if the battery is dead then the truck won't stay running for long. I had my '99 G/A do the same thing couple years ago, turned out the alternator was bad. Todays "charging"systems no...
06-02-2007, 10:58 PM
Replies: 8
Views: 1,611
Posted By 20Blazer00

RE: front end noise

The metal grinding sound could be CV joint in a half shaft but the symptoms you explained earlier indicate that the actuator inside the front differential is not completely disengaging the pass side...
06-01-2007, 09:47 PM
Replies: 1
Views: 920
Posted By 20Blazer00

RE: key is hard to turn

Sounds like the lock cylinder needs replacing....remove the steering column cover and you should find a small hole to put an allen wrench/screw driver into to push on and remove the cylinder....with...
Showing results 1 to 50 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.