Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: Project96
Showing results 1 to 9 of 9
Search took 0.00 seconds.
Forum: Lighting & Electrical
08-03-2013, 12:45 PM
Replies: 3
Views: 1,202
Posted By Project96

I had to break the rear panel off to gain access...

I had to break the rear panel off to gain access to the rear window latch. Thanks for the link. The little blue thing is exactly what I need.

Now the damn transfer case went out last week too. ...
Forum: Lighting & Electrical
07-14-2013, 02:01 PM
Replies: 3
Views: 1,202
Posted By Project96

Rear hutch won't open

Yesterday I went to throw out some trash as I usually do. Hatch opened just fine... Later in the eve I went to open the hatch glass & the actuator sounded different & wouldn't release the latch to...
Forum: 2nd Generation S-series (1995-2005) Tech
05-11-2012, 07:11 PM
Replies: 1
Views: 1,456
Posted By Project96

Distributor timing???

I'm about to replace the lower intake manifold gasket due to a coolant leak. I can't find any info on timing degree BTDC when I reassemble. Should I just mark the intake & dizzy & hope for the best...
Forum: 2nd Generation S-series (1995-2005) Tech
05-11-2012, 07:07 PM
Replies: 15
Views: 10,634
Posted By Project96

I have an ebay one in my 02 with about 15000...

I have an ebay one in my 02 with about 15000 miles on it. Works great so far with no problems. Only thing I had to do was re-wire one of the plugs. But the kit comes with the plug & crimp terminals....
Forum: General Chat
11-17-2010, 03:24 PM
Replies: 4
Views: 912
Posted By Project96

Is there a thread or sticky with the engine &...

Is there a thread or sticky with the engine & drivetrain specs here? This is from another forum but used as an example. This is what im searching for.


What are the basic specs for the...
Forum: 2nd Generation S-series (1995-2005) Tech
11-16-2010, 01:53 PM
Replies: 5
Views: 1,201
Posted By Project96

The front hub & bearings are the same thing. When...

The front hub & bearings are the same thing. When you replace the bearings, you replace the hub. I got mine from advanced auto for about $100.00 a piece. I olny did on e side at a time. Have about 6...
Forum: Lifting Tech
11-16-2010, 01:36 PM
Replies: 40
Views: 26,975
Posted By Project96

So where do I find them. I need an alignment now...

So where do I find them. I need an alignment now but want to wait till I get the keys in. I need to do a ride hight measurement as well.
Forum: Lifting Tech
11-16-2010, 10:03 AM
Replies: 40
Views: 26,975
Posted By Project96

Does anybody have the part # for the tortion...

Does anybody have the part # for the tortion keys? I ordered a set from amazon that according to their cross reference would fit. (Daystar KG09110). I want to get these in and aligned before winter...
Forum: General Chat
11-06-2010, 01:48 PM
Replies: 4
Views: 912
Posted By Project96

I'm here to seek the same info. Actually suprised...

I'm here to seek the same info. Actually suprised that there isnt a spec thread on the main page. I have an 02 blazer ls & Im about to put the 2nd t-case in it in about 3 yrs. I was wondering if...
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands