Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: Chris Jessee
Showing results 1 to 20 of 20
Search took 0.00 seconds.
Forum: 2nd Generation S-series (1995-2005) Tech
10-05-2013, 08:43 PM
Replies: 30
Views: 25,644
Posted By Chris Jessee

I have a 96 Jimmy with manual climate control. I...

I have a 96 Jimmy with manual climate control. I now only have hot air with temp selector in all positions. Everything else works as it should. Could this be a blend actuator problem? If so, how do...
Forum: 2nd Generation S-series (1995-2005) Tech
02-18-2013, 11:02 AM
Replies: 25
Views: 3,928
Posted By Chris Jessee

I am happy to say that I do believe my 4wd is...

I am happy to say that I do believe my 4wd is fixed. I disconnected the tccm for about 30 to 45 minutes and did the ignition cycle 5 times. It now works in all positions. I cycled it through all 3...
Forum: 2nd Generation S-series (1995-2005) Tech
02-18-2013, 08:06 AM
Replies: 25
Views: 3,928
Posted By Chris Jessee

I didn't try it when I changed the encoder. I do...

I didn't try it when I changed the encoder. I do know that it does work in all positions, I can get 4hi to work occasionally. That is one reason that I am leaning towards replacing the tccm. The new...
Forum: 2nd Generation S-series (1995-2005) Tech
02-17-2013, 08:10 PM
Replies: 25
Views: 3,928
Posted By Chris Jessee

Due to the fact that it gave me lots of trouble...

Due to the fact that it gave me lots of trouble changing the encoder motor, I don't really want to pull it back off and try shifting it manually. If it works correctly a few times after disconnecting...
Forum: 2nd Generation S-series (1995-2005) Tech
02-17-2013, 02:16 PM
Replies: 25
Views: 3,928
Posted By Chris Jessee

I haven't tried it with the new encoder. The last...

I haven't tried it with the new encoder. The last time I disconnected the tccm, it worked in all positions, for a few tries
Forum: 2nd Generation S-series (1995-2005) Tech
02-17-2013, 01:50 PM
Replies: 25
Views: 3,928
Posted By Chris Jessee

This is my daily driver, 177,000 miles on it....

This is my daily driver, 177,000 miles on it. Runs great. Getting new upper and lower ball joints, tires, and alignment this week. Already replaced the idler arm and I have put a lot of money into...
Forum: 2nd Generation S-series (1995-2005) Tech
02-17-2013, 01:41 PM
Replies: 25
Views: 3,928
Posted By Chris Jessee

I pulled the 4wd and tranny fuse last night, left...

I pulled the 4wd and tranny fuse last night, left them out for about and hour. Still wont go into 4hi and I still have a code 2.
Forum: 2nd Generation S-series (1995-2005) Tech
02-17-2013, 12:56 PM
Replies: 25
Views: 3,928
Posted By Chris Jessee

The 4WD fuse?

The 4WD fuse?
Forum: 2nd Generation S-series (1995-2005) Tech
02-17-2013, 12:24 PM
Replies: 25
Views: 3,928
Posted By Chris Jessee

Still showing code 2. Do I need to disconnect the...

Still showing code 2. Do I need to disconnect the battery or unplug the connector at the TCCM?
Forum: 2nd Generation S-series (1995-2005) Tech
02-16-2013, 06:49 PM
Replies: 25
Views: 3,928
Posted By Chris Jessee

I pulled the 4WD fuse and the tranny fuse and...

I pulled the 4WD fuse and the tranny fuse and left them out for about an hour. I then cycled the key on and off 5 times waiting for the lights to stop flashing each time before turning it off each...
Forum: 2nd Generation S-series (1995-2005) Tech
02-16-2013, 05:07 PM
Replies: 25
Views: 3,928
Posted By Chris Jessee

What is the correct way to rest the tccm? I...

What is the correct way to rest the tccm? I haven't reset it and that may be all that it needs.
Forum: 2nd Generation S-series (1995-2005) Tech
02-16-2013, 10:34 AM
Replies: 25
Views: 3,928
Posted By Chris Jessee

I replaced the encoder motor. It still isn't...

I replaced the encoder motor. It still isn't going into 4HI, I am thinking that I need to replace either the tccm or the axle switch. If I am not mistaken, the axle switch is open when in 2HI and...
Forum: Steering, Suspension & Drivetrain
02-07-2013, 07:15 AM
Replies: 4
Views: 992
Posted By Chris Jessee

I have found a tie rod separator that I am going...

I have found a tie rod separator that I am going to try. I will let you know how it works.
Forum: Steering, Suspension & Drivetrain
02-06-2013, 01:16 AM
Replies: 4
Views: 992
Posted By Chris Jessee

Idler arm

I have a 96 GMC Jimmy 4 door 4x4. I am trying to replace the idler arm. Does anyone know any tricks for getting it out of the center link. I have tried a pickle fork and a 4lb hammer.
Forum: 2nd Generation S-series (1995-2005) Tech
01-22-2013, 10:26 AM
Replies: 25
Views: 3,928
Posted By Chris Jessee

I have a 96 with the NV233 t-case (3 button). I...

I have a 96 with the NV233 t-case (3 button). I am having similar issues as the other guys in this thread. With the exception that my four wheel drive works intermittently. Also sometimes when I...
Forum: Engine & Transmission
01-22-2013, 10:05 AM
Replies: 9
Views: 1,884
Posted By Chris Jessee

It seems that the fuel lines were the problem. It...

It seems that the fuel lines were the problem. It is still running good. No misses or extended cranking, and no DTC's. I would like to thank Captain Hook for your instructions.
Forum: Engine & Transmission
01-19-2013, 10:19 PM
Replies: 9
Views: 1,884
Posted By Chris Jessee

I drove it today for about 80 miles. Mixture of...

I drove it today for about 80 miles. Mixture of city and highway driving, but mostly highway. The service engine light did come back on, but there are no noticeable driving issues. I will get the...
Forum: Engine & Transmission
01-18-2013, 09:25 PM
Replies: 9
Views: 1,884
Posted By Chris Jessee

I haven't yet purchased a fuel pressure tester....

I haven't yet purchased a fuel pressure tester. I did find out today that the evap line and return line were swapped at the fuel pump. I haven't had a chance to take it on a long drive, but the...
Forum: Engine & Transmission
01-18-2013, 08:04 AM
Replies: 9
Views: 1,884
Posted By Chris Jessee

In the process of checking the cap and rotor, I...

In the process of checking the cap and rotor, I found that the distributor shaft seems to have excessive vertical play in it. I am going to compare the play in the shaft to a new one.
Forum: Engine & Transmission
01-17-2013, 09:01 AM
Replies: 9
Views: 1,884
Posted By Chris Jessee

96 Blazer multiple codes

I have a 96 4 door 4x4. The codes I have now are po175 po300 po440. I have replaced the IAC valve, injector assembly, plugs, wires, cap, and rotor. Fuel pump is a little over a year old.
It runs...
Showing results 1 to 20 of 20


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands