Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: *2000ZR2*
Showing results 1 to 11 of 11
Search took 0.01 seconds.
Forum: 2nd Generation S-series (1995-2005) Tech
08-27-2009, 07:02 PM
Replies: 3
Views: 921
Posted By *2000ZR2*

Unhappy The sound from the exhaust that I heard yesterday...

The sound from the exhaust that I heard yesterday was coming from the muffler and it was not the typical hot exhaust, pop/crackle sounds. I was racing the throttle quite a bit, so maybe it was just a...
Forum: 2nd Generation S-series (1995-2005) Tech
08-26-2009, 05:49 PM
Replies: 3
Views: 921
Posted By *2000ZR2*

yep, another heisitation post

Truck is a 2000 ZR blazer with just a little over a hundred thousand miles. It has a strong mis/heisitation when the throttle is opened part way(2000-2500 RPMs). When at WOT it runs smooth again. It...
Forum: 2nd Generation S-series (1995-2005) Tech
08-17-2009, 06:04 PM
Replies: 4
Views: 16,758
Posted By *2000ZR2*

Good tip and yep sometimes that works. Your fan...

Good tip and yep sometimes that works. Your fan clutch was probably properly torqued and your method should usually work. I spent an hour trying different ways of holding the water pump pulley when I...
Forum: 2nd Generation S-series (1995-2005) Tech
08-17-2009, 05:54 PM
Replies: 4
Views: 842
Posted By *2000ZR2*

Is it leaking where the water pump bolts to the...

Is it leaking where the water pump bolts to the block, or above the timing cover(near the thermostat housing)? If its where the water pump bolts to the block then your seals are probably bad....
Forum: 2nd Generation S-series (1995-2005) Tech
08-17-2009, 05:40 PM
Replies: 4
Views: 1,052
Posted By *2000ZR2*

Before you go and buy a new pump, you may at...

Before you go and buy a new pump, you may at least want to run a fuel pressure test and make sure that is your problem first. I'm not sure if AC Delco and Delphi are the same company, but GM uses...
Forum: 2nd Generation S-series (1995-2005) Tech
08-10-2009, 02:57 PM
Replies: 5
Views: 977
Posted By *2000ZR2*

I couldn't tell you about the differences between...

I couldn't tell you about the differences between them, but I used the felpro set on my lower intake a couple of years ago. Probley got at least 30,000 miles on since. No leaks yet.
Forum: 2nd Generation S-series (1995-2005) Tech
08-09-2009, 08:47 PM
Replies: 3
Views: 925
Posted By *2000ZR2*

To gain access to the crush sleeve from outside,...

To gain access to the crush sleeve from outside, I would remove the yoke, pinion seal and then the top bearing? You are saying that to properly set the pinion bearing tension that the differential is...
Forum: 2nd Generation S-series (1995-2005) Tech
08-09-2009, 08:15 PM
Replies: 17
Views: 3,010
Posted By *2000ZR2*

I think you are talking about the encoder motor....

I think you are talking about the encoder motor. It is kind of common problem. Also the corrosion on the TCCM is pretty common too. The wires were so corroded on mine that they were starting to pull...
Forum: 2nd Generation S-series (1995-2005) Tech
08-09-2009, 08:09 PM
Replies: 2
Views: 663
Posted By *2000ZR2*

It sounds like the encoder motor on your transfer...

It sounds like the encoder motor on your transfer case is stuck. Happened on mine when I was in 4-lo a couple years ago. That click that you hear is the transfer case control module. Mine is located...
Forum: Engine & Transmission
08-09-2009, 07:58 PM
Replies: 125
Views: 51,127
Posted By *2000ZR2*

Wish I would have known about this last winter....

Wish I would have known about this last winter. My ABS module somehow became internally shorted so the pump would run continuosly, even with the ignition off. After the dealer quoted me over 800...
Forum: 2nd Generation S-series (1995-2005) Tech
08-09-2009, 05:00 PM
Replies: 3
Views: 925
Posted By *2000ZR2*

Rear End Blunder

My truck is a 2000 Blazer ZR2. Automatic transmission and about 101,000 on the odometer. I just finished replacing all the seals in the rear end and made the mistake of over tighting the pinion nut...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands