Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: kenlani
Showing results 1 to 21 of 21
Search took 0.01 seconds.
Forum: 2nd Generation S-series (1995-2005) Tech
02-06-2013, 01:45 PM
Replies: 12
Views: 8,841
Posted By kenlani

I just realized I havent updated this thread -- ...

I just realized I havent updated this thread -- I replaced switch , blew out lines and had input shaft seal replaced (Transfer case was way over full) also had bad u-joint -- did'nt blow out all the...
Forum: 2nd Generation S-series (1995-2005) Tech
12-29-2012, 12:09 AM
Replies: 32
Views: 19,151
Posted By kenlani

Thumbs up Well I have finally worked it all out-- bad...

Well I have finally worked it all out-- bad vacuum switch and Transfer Case input shaft seal. I replaced the vacuum switch, blew out the lines to/from the switch and actuator, capped/plugged the HVAC...
Forum: 2nd Generation S-series (1995-2005) Tech
12-18-2012, 08:39 PM
Replies: 8
Views: 9,813
Posted By kenlani

Me Too!.... Me Too!

Me Too!.... Me Too!
Forum: 2nd Generation S-series (1995-2005) Tech
12-13-2012, 02:45 PM
Replies: 12
Views: 8,841
Posted By kenlani

Thanks for the great advice --I really appreciate...

Thanks for the great advice --I really appreciate your help-----I think I will wait to do the dash work(holy moly!) But I'm Wondering why the engine wouldn't just suck the fluid in so I dont have...
Forum: 2nd Generation S-series (1995-2005) Tech
12-08-2012, 06:57 PM
Replies: 1
Views: 5,259
Posted By kenlani

Heater/AC control vacuum lines -96 Blazer

OK, Had 4WD actuator problem so I replaced the transfer case vacuum switch (PITA) and blew out the vacuum lines and vent to the switch-problem fixed! but I see the tranny fluid in the vacuum line...
Forum: 2nd Generation S-series (1995-2005) Tech
12-08-2012, 06:43 PM
Replies: 12
Views: 8,841
Posted By kenlani

Okey Dokey---I replaced the switch (what a...

Okey Dokey---I replaced the switch (what a PITA-remove skid plate , get short wrench, awkward position with short strokes to get out- then replaced) I then blew out the vacuum lines and the vent...
Forum: 2nd Generation S-series (1995-2005) Tech
12-08-2012, 06:35 PM
Replies: 8
Views: 878
Posted By kenlani

try pulling fuse 13(I believe) lettin it sit then...

try pulling fuse 13(I believe) lettin it sit then replace --this resets something , either the pushbutton set or the encoder not sure but it sometimes worked for me
Forum: 2nd Generation S-series (1995-2005) Tech
12-04-2012, 12:10 PM
Replies: 32
Views: 19,151
Posted By kenlani

Yes, thank you gentlemen very much for the great...

Yes, thank you gentlemen very much for the great help here--- One last question? I just havent quite figured out the vacuum switch though-I understand the source and actuator vacuum at the switch...
Forum: 2nd Generation S-series (1995-2005) Tech
12-03-2012, 04:45 PM
Replies: 32
Views: 19,151
Posted By kenlani

Attached to the hose next to the tranny dipstick...

Attached to the hose next to the tranny dipstick tube is what doesn't appear to be a "filter" but rather a black plastic little check valve thing- this allows free flow out but limited flow in--am I...
Forum: 2nd Generation S-series (1995-2005) Tech
12-03-2012, 02:53 PM
Replies: 32
Views: 19,151
Posted By kenlani

Thank You Captain for the quick reply---Oh...

Thank You Captain for the quick reply---Oh Boy--looks like I've got work to do before the snow------Again thanks for the reply--but I'm still puzzled as to how the transfer case sucks fluid from the...
Forum: 2nd Generation S-series (1995-2005) Tech
12-03-2012, 02:17 PM
Replies: 12
Views: 8,841
Posted By kenlani

96 Blazer Transfer Case Vacuum Switch

As I was checking my vacuum hose to the 4WD actuator at the firewall I discovered tranny fluid in the vacuum hoses which means I have a faulty vacuum switch at the transfer case.....I will clean out...
Forum: 2nd Generation S-series (1995-2005) Tech
12-03-2012, 12:41 PM
Replies: 32
Views: 19,151
Posted By kenlani

Oil in Lines

I was following this thread to fix my 96 Blazers problem shifting into 4HI-- I was checking my actuator vacuum line for cracks/leaks and when I pulled the line off the tee---tranny fluid leaks like...
Forum: 2nd Generation S-series (1995-2005) Tech
01-21-2010, 12:49 PM
Replies: 1
Views: 1,159
Posted By kenlani

Windshield weatherstrip came out

My 96 Blazer accumulated about 2' of snow yesterday--I knocked most of it off then went to town--as the snow on the roof started to slide off, it peeled out the upper windshield weatherstrip.... the...
Forum: Engine & Transmission
11-11-2009, 09:13 AM
Replies: 10
Views: 16,477
Posted By kenlani

:icon_wink:Big Thanks to all who posted in this...

:icon_wink:Big Thanks to all who posted in this thread, I've finished my valvebody rebuild/install and have a couple of suggestions to help others in this task:

--I made a scrap wood template of...
Forum: Engine & Transmission
10-14-2009, 11:50 AM
Replies: 25
Views: 44,469
Posted By kenlani

Many thanks to swartlkk and old skool but have...

Many thanks to swartlkk and old skool but have two questions to relieve my confusion---

----I have a removable clip under the plastic at the fitting -dont I just remove that and pull out the...
Forum: Engine & Transmission
10-09-2009, 11:39 PM
Replies: 25
Views: 44,469
Posted By kenlani

--Thank You...is there any special thing about...

--Thank You...is there any special thing about loosening the fitting? there seems to be some kinda plastic part to it---
--So I wont be flushing the cooler itself?
again thanks
Forum: Engine & Transmission
10-09-2009, 07:30 PM
Replies: 2
Views: 941
Posted By kenlani

difficulty in flushing tranny 96 Blazer 4wd

I've been reading up and preparing for a valve body replacement in my 96 Blazer, Put it on stands and went underneath it today, first thing was to flush the tranny----came to an immediate halt--how...
Forum: Engine & Transmission
10-09-2009, 07:06 PM
Replies: 25
Views: 44,469
Posted By kenlani

How to disconnect tranny cooler return line?

How and where did you disconnect the cooler return line? I have a 96 4wd Blazer and went underneath today to do the tranny flush but discovered that I cant figure out how to disconnect the return...
Forum: 2nd Generation S-series (1995-2005) Tech
10-07-2009, 11:07 AM
Replies: 3
Views: 1,073
Posted By kenlani

You might want to consider the other wheels as...

You might want to consider the other wheels as well--when Sams replaced the tires they may have over-torqued them all--the others may well be a problem waiting to happen
Forum: Website Problems and Suggestions
09-06-2009, 11:30 AM
Replies: 5
Views: 966
Posted By kenlani

Is there a way to use the IMG code that does...

Is there a way to use the IMG code that does show?--there are some pics on Tranny Valve Body Replacement that I really wanna see bad
Forum: Engine & Transmission
09-06-2009, 11:16 AM
Replies: 10
Views: 16,477
Posted By kenlani

I really appreciate this thread, but Can't see...

I really appreciate this thread, but Can't see the images--I guess the site was hit with a bug that erased some images--If you could repost the images or tell me how to view them I'd appreciate it ...
Showing results 1 to 21 of 21


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands