Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: Big Blaze
Showing results 1 to 17 of 17
Search took 0.00 seconds.
Forum: Builds
12-20-2009, 12:08 PM
Replies: 7
Views: 2,836
Posted By Big Blaze

It could be the fan, but it would vibrate all the...

It could be the fan, but it would vibrate all the time. You should probably look at drivetrain, possibly a problem with driveshaft balance.
Forum: Lifting Tech
12-18-2009, 01:58 PM
Replies: 5
Views: 1,330
Posted By Big Blaze

265/75R15 is bigger than the factory tire size,...

265/75R15 is bigger than the factory tire size, so if that is in fact the size of the tire you are not sagging, just rubbing due to the larger tires.
Forum: Builds
12-18-2009, 01:40 PM
Replies: 7
Views: 2,836
Posted By Big Blaze

The injector spider you mentioned will not work...

The injector spider you mentioned will not work on your truck, only 1996 and up engines. You have a CPI Vortec engine, which basically has one injector and tubes to send the fuel to each cylinder,...
Forum: Tires and Wheels
06-06-2009, 09:14 PM
Replies: 41
Views: 5,388
Posted By Big Blaze

You should check out Jigg's Blazer at the Synergy...

You should check out Jigg's Blazer at the Synergy Offroad Garage. He has the setup you are trying for.
Forum: Tires and Wheels
06-06-2009, 08:39 PM
Replies: 12
Views: 858
Posted By Big Blaze

I would suggest having them sand blasted. That...

I would suggest having them sand blasted. That will take the finish off without leaving deep scratches or any kind of grain from sanding. Then have them re-coated. I believe that they make a clear...
Forum: Tires and Wheels
05-07-2009, 09:18 PM
Replies: 13
Views: 1,364
Posted By Big Blaze

Are you sure? Oh well, my bad, you're probably...

Are you sure? Oh well, my bad, you're probably right.
Forum: Tires and Wheels
05-01-2009, 04:00 PM
Replies: 13
Views: 1,364
Posted By Big Blaze

All 2wd wheels, including ZQ8s and Xtremes, along...

All 2wd wheels, including ZQ8s and Xtremes, along with 82-92 F-bodies, have 4.25" backspacing. 1993-2002 Camaros and 1992-up Corvettes have the same backspacing as stock 4wd wheels, 6".
Forum: Tires and Wheels
05-01-2009, 03:53 PM
Replies: 41
Views: 5,388
Posted By Big Blaze

If you have aftermarket torsion keys and you got...

If you have aftermarket torsion keys and you got 3" of lift out of them, then you are going to destroy your front end. The most you should ever lift the front end by cranking the torsion bars is 2",...
Forum: Steering, Suspension & Drivetrain
05-01-2009, 03:39 PM
Replies: 4
Views: 2,267
Posted By Big Blaze

Diversified Creations makes an adapter that...

Diversified Creations makes an adapter that allows you to install S10 ABS Bearings and discs on the Dana 30 Wrangler axle. Also, Sky's Offroad Manufacturing makes a solid axle swap spring hanger kit...
Forum: Lifting Tech
05-01-2009, 03:33 PM
Replies: 4
Views: 762
Posted By Big Blaze

I agree with these guys. However, how many miles...

I agree with these guys. However, how many miles were on the CVs when you installed the lift. They could have been about to die anyway. On my 1992 Blazer, cranking the torsion bars 2" ruined CV...
Forum: Lifting Tech
03-31-2009, 11:51 AM
Replies: 4
Views: 964
Posted By Big Blaze

The Fabtech lift kit in the link is for a full...

The Fabtech lift kit in the link is for a full size Blazer, or Tahoe. Don't you have an S-series?
Forum: Lifting Tech
09-30-2008, 09:50 AM
Replies: 15
Views: 7,413
Posted By Big Blaze

RE: Mods with a 4.3L?

The bumper is made by a company called Animal 4x4. They make bolt-on, weld-on, and bumper kits. They also make rear bumpers for Blazers.
Forum: Engine & Internal
09-30-2008, 09:31 AM
Replies: 49
Views: 10,385
Posted By Big Blaze

RE: hot rodding a 4.3L

Just remember that on those stroker cranks that they are offset ground, so it is taking away from the strength of the factory crank. For forced induction it would probably be best to stay with the...
Forum: Engine & Internal
09-30-2008, 09:08 AM
Replies: 4
Views: 4,951
Posted By Big Blaze

RE: lost my overdrive???!!!

It could just be the torque converter lock up clutch. One of the sensors in early 4L60Es was in a hole that was too big for it and would let fluid seep past, telling the computer not to lock up the...
Forum: Engine & Internal
09-10-2008, 03:56 PM
Replies: 7
Views: 15,179
Posted By Big Blaze

RE: aftermarket heads

Brodix makes aluminum heads for the 4.3.
Forum: Off Roading
08-29-2008, 11:29 AM
Replies: 24
Views: 3,247
Posted By Big Blaze

RE: Installed my Bushwacker flares today

Couldn't you just cut the flares from a 2 door so the door could open. I've seen it done before. It looks pretty easy.
Forum: 2nd Generation S-series (1995-2005) Tech
03-24-2008, 11:46 AM
Replies: 8
Views: 6,282
Posted By Big Blaze

RE: stinger front bumper

Hey, have you guys thought about building a set of rock sliders for a 4 door Blazer. Nobody seems to make any.
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands