Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: vega7677
Showing results 1 to 8 of 8
Search took 0.00 seconds.
Forum: 2nd Generation S-series (1995-2005) Tech
12-07-2010, 03:24 PM
Replies: 23
Views: 24,083
Posted By vega7677

Kyle, My new spider came in this morning. I...

Kyle,
My new spider came in this morning. I went out after lunch today & pulled the upper intake , cleaned it & the lim , installed the new spider , put it back together . Now I have No...
Forum: 2nd Generation S-series (1995-2005) Tech
12-04-2010, 10:02 AM
Replies: 23
Views: 24,083
Posted By vega7677

Kyle, Went out this morning & checked the...

Kyle,
Went out this morning & checked the injector pins on the connector , none bent or out of shape. Right now I am running Seafoam in the fuel , letting it run for awhile & then letting it sit for...
Forum: 2nd Generation S-series (1995-2005) Tech
12-03-2010, 04:24 PM
Replies: 23
Views: 24,083
Posted By vega7677

Thanks Kyle, I will check that tomorrow, just...

Thanks Kyle,
I will check that tomorrow, just went down to Chevy dealership to see a buddy & get his price on spider #12568332 (new # is 19210688) , he can get it for $209 . Checked gm parts direct...
Forum: 2nd Generation S-series (1995-2005) Tech
12-03-2010, 12:30 PM
Replies: 23
Views: 24,083
Posted By vega7677

Kyle , I just went out to my garage & pulled...

Kyle ,
I just went out to my garage & pulled the plug on #6 , had some black soot around the edge , but electrode was clean, changed wire , cleared code .
Started it up & still threw P0306 code,...
Forum: 2nd Generation S-series (1995-2005) Tech
12-03-2010, 09:17 AM
Replies: 23
Views: 24,083
Posted By vega7677

Kyle, Did you ever do a rebuild on a EDI dist....

Kyle,
Did you ever do a rebuild on a EDI dist. ? How much clearance should one have when you pull up on the dist. shaft ? If it has too much ,why would it only give a P0306 ?
I can clear the P0306...
Forum: 2nd Generation S-series (1995-2005) Tech
12-02-2010, 05:27 PM
Replies: 23
Views: 24,083
Posted By vega7677

Angry Ignition advance question ....

Guys , bought this 96 Blazer 2 door that was not running. Replaced timing gear & chain, cap & rotor,wires & plugs . Got it running & had a p0300 code.Bought 4 new 02 sensors & lost the P0300, but now...
Forum: Engine & Transmission
11-25-2010, 09:48 AM
Replies: 3
Views: 1,166
Posted By vega7677

I'm just checking everthing that might have...

I'm just checking everthing that might have anything to do with the P0300 code. 63 FP on prime,56 while idleing,has good compression on all cylinders , new cap & rotor, new wires & plugs , new dist...
Forum: Engine & Transmission
11-24-2010, 08:27 AM
Replies: 3
Views: 1,166
Posted By vega7677

Grounds to heads

Guys, just bought 96 Blazer LS 2 door. I have been chasing P0300 code on it. Was trying to check grds , on grds to the heads,how do you even see them, let alone check them !!!
Sherman
Showing results 1 to 8 of 8


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands