Blazer Forum - Chevy Blazer Forums - Search Results

Community
Search
Search: Posts Made By: jeffrozar
Showing results 1 to 19 of 19
Search took 0.00 seconds.
07-21-2016, 07:53 AM
Replies: 5
Views: 1,391
Posted By jeffrozar

I also got the Hayden #1009 from O'Reilly auto...

I also got the Hayden #1009 from O'Reilly auto parts for $19.99. Hooked it up and used the enclosed tie to cinch it to the bracket after I cut off the metal tubing and buffed them down on the bench...
07-21-2016, 07:50 AM
07-19-2016, 04:57 AM
Replies: 5
Views: 1,391
Posted By jeffrozar

Where did you mount it? Any pictures?

Where did you mount it? Any pictures?
07-17-2016, 07:37 PM
Replies: 3
Views: 768
Posted By jeffrozar

Question '98 ZR2, extra dangling plug in front of a/c condenser?

So I took the front grill off of my Blazer, and I found a two-plug wire not plugged into anything. It comes off of the plastic/coil-wrapped wire harness that runs below and in front of the a/c...
07-17-2016, 07:30 PM
Replies: 5
Views: 1,391
Posted By jeffrozar

Question '98 ZR2, SAE 30R7 for oil?

So my "coil" of tubing that the power steering pump uses in front of the A/C condenser sprung a leak. In lieu of replacing it, I simply cut off the lines behind the headlight and ran an SAE 30R7 fuel...
07-17-2016, 07:21 PM
Replies: 9
Views: 1,433
Posted By jeffrozar

So I forgot to put back the PCV valve and hose....

So I forgot to put back the PCV valve and hose. Rough idle suddenly turned smooth!
07-03-2016, 02:28 PM
Replies: 9
Views: 1,433
Posted By jeffrozar

Fixed it! Great video! Lined up the timing marks...

Fixed it! Great video! Lined up the timing marks (noted the two notches as in the image) on the crank flywheel and the engine. Indeed it was off and not pointing at the "6" embossed on the rotor!...
07-03-2016, 08:00 AM
Replies: 9
Views: 1,433
Posted By jeffrozar

Wouldn't the wrong tooth mean it wouldn 't run at...

Wouldn't the wrong tooth mean it wouldn 't run at all, or wouldn't run at higher rpm?
07-02-2016, 06:10 PM
Replies: 9
Views: 1,433
Posted By jeffrozar

Question '98 ZR2, P0345, rough/unsustainable idle

I replaced the intake manifold gasket on my '98 ZR2. Not too bad, but couldn't get the fuel lines off and the power steering pump/ac bracket wouldn't wiggle completely off, but I did manage to get...
05-12-2015, 06:53 AM
Replies: 4
Views: 5,028
Posted By jeffrozar

Thanks Hook! I got that Felpro p/n for it +...

Thanks Hook! I got that Felpro p/n for it + replacement intake manifold bolts. I also read the ignition coil is a high output from the factory starting with the 2nd gen Blazer. Dealer wanted $950 to...
05-04-2015, 12:51 PM
Replies: 4
Views: 5,028
Posted By jeffrozar

Any recommended gaskets/upgraded gasket material...

Any recommended gaskets/upgraded gasket material to use? Or just use OEM?
05-04-2015, 11:29 AM
Replies: 4
Views: 5,028
Posted By jeffrozar

Coolant leaking under A/C on '98 ZR2

I have a '98 Blazer ZR2 with the V6 and the coolant is leaking out at the connection that's underneath the A/C compressor. Looks like some type of pipe - it has the black plastic heat wrapping weave...
11-04-2011, 03:49 PM
Replies: 2
Views: 2,029
Posted By jeffrozar

Is the encoder motor connected to the cable that...

Is the encoder motor connected to the cable that goes up to the diaphragm?
11-04-2011, 03:25 PM
Replies: 2
Views: 2,029
Posted By jeffrozar

Stuck in 4wd HI; goes 4HI/4LO ok, won't go to 2wd HI

1998 Blazer ZR2, Stuck in 4wd HI; goes 4HI/4LO ok, won't go to 2wd HI. I can switch from 4HI to 4LO to 4HI all day, but it won't go into 2HI.

I pulled the battery and tray out and found the...
11-04-2011, 10:08 AM
Replies: 0
Views: 1,755
Posted By jeffrozar

Stuck in 4wd HI; goes 4HI/4LO ok, won't go to 2wd HI

1998 Blazer ZR2, Stuck in 4wd HI; goes 4HI/4LO ok, won't go to 2wd HI. I can switch from 4HI to 4LO to 4HI all day, but it won't go into 2HI.

I pulled the battery and tray out and found the...
08-01-2009, 07:35 PM
Replies: 3
Views: 763
Posted By jeffrozar

Thanks. I was hoping to buy a pre-made ones I...

Thanks. I was hoping to buy a pre-made ones I just have to bend.
08-01-2009, 07:19 PM
Replies: 3
Views: 763
Posted By jeffrozar

Where to buy brake lines?

My 1998 ZR2 left front brake line rusted through at the hose connection and now I need to replace it. I got a new hose on from AutoZone, new banjo bolt, new bleeder screws.

My question is where...
01-21-2009, 08:06 AM
Replies: 2
Views: 518
Posted By jeffrozar

RE: Where to buy hatch dampers?

Thanks for the awesome reply with the links! That was easy!
01-20-2009, 10:12 PM
Replies: 2
Views: 518
Posted By jeffrozar

Where to buy hatch dampers?

Hi, everyone. I'm new to the board.

First problem: I have a '98 ZR2, and the back hatch won't stay up. I think the dampers need replacing. Where do I get them? I did a lookup on autozone.com,...
Showing results 1 to 19 of 19


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands