Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: billymac49
Showing results 1 to 10 of 10
Search took 0.01 seconds.
Forum: Engine & Transmission
07-07-2009, 05:37 AM
Replies: 6
Views: 5,997
Posted By billymac49

the computer sees that the transfer is not...

the computer sees that the transfer is not completing a shift. can be mechanical or electrical problem. encoder motors are known to go bad.
Forum: Engine & Transmission
07-06-2009, 01:59 PM
Replies: 3
Views: 919
Posted By billymac49

i work at a tranny shop and that's all we use....

i work at a tranny shop and that's all we use. look at other so called brand name clutches or pressure plates and you probably will see Luk stamped on there. You may even see Luk stamped on OEM. Some...
Forum: Steering, Suspension & Drivetrain
07-02-2009, 09:07 AM
Replies: 2
Views: 1,395
Posted By billymac49

did you check the u-joints by removing the shaft?...

did you check the u-joints by removing the shaft? do the u-joints seem notchy when moved?when shaft is removed check diff. yoke for any roughness or play.
Forum: Full Size K5 (1969-1991) GMT415 (1992-1994) Tech
07-02-2009, 08:42 AM
Replies: 4
Views: 9,464
Posted By billymac49

any fluid leaking? check all connections and...

any fluid leaking? check all connections and lines for leaks. check master in the engine compartment and under the dash for any wetness. also deteriorated rubber lines can give you a spongy pedal...
Forum: 2nd Generation S-series (1995-2005) Tech
07-02-2009, 08:36 AM
Replies: 3
Views: 517
Posted By billymac49

dealer carries the cable and they are not that...

dealer carries the cable and they are not that bad to change out. remove battery and tray to access the canister.
Forum: 2nd Generation S-series (1995-2005) Tech
07-02-2009, 08:33 AM
Replies: 3
Views: 771
Posted By billymac49

normal fuel pres. psi. should be around 60-66...

normal fuel pres. psi. should be around 60-66 psi. it should hold pressure for i'd say a good 5-10 min. without any drastic press. loss. if so then the fuel is bleeding off somewhere (injector,...
Forum: Engine & Transmission
06-05-2009, 07:14 AM
Replies: 2
Views: 1,562
Posted By billymac49

how is the fluid level and condition. low fluid...

how is the fluid level and condition. low fluid level could make it shift abnormally. check engine light on?
Forum: Engine & Transmission
06-05-2009, 07:06 AM
Replies: 4
Views: 931
Posted By billymac49

there is some truth to that. changing the can...

there is some truth to that. changing the can lead you to a rebuild quicker than you want. the new fluid acts like a detergent to the frictions cleaning the linings. either way if the fluid is that...
Forum: Engine & Transmission
06-05-2009, 07:00 AM
Replies: 5
Views: 2,851
Posted By billymac49

a quick way to test this is to remove both lines...

a quick way to test this is to remove both lines at the tranny. clamp a rubber hose to one of the lines and put into a bucket. use a blow gun and shop air to blow the lines out. this will blow the...
Forum: New Member Area
06-05-2009, 06:53 AM
Replies: 8
Views: 429
Posted By billymac49

new to forum in ct

hey guys. i'm new here. i have had plenty of blazers over the years and stumbled across this site. currently i have a 89 k5 a w/ 4" lift that's a project/daily driver and a 02 blazer/family...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands