Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: spkremer
Showing results 1 to 10 of 10
Search took 0.00 seconds.
Forum: Engine & Transmission
09-05-2010, 12:58 PM
Replies: 33
Views: 5,044
Posted By spkremer

Thumbs up nice..and BTW your the hottest mechanic i've ever...

nice..and BTW your the hottest mechanic i've ever seen, too bad your married and live 4000 miles away =(
keep up the good work!
Forum: Engine & Transmission
09-04-2010, 09:32 PM
Replies: 33
Views: 5,044
Posted By spkremer

nice..i just got rid of that 0300 on mine, spider...

nice..i just got rid of that 0300 on mine, spider injector, which was also causing lean and rich codes to pop up,
there are a bunch of threads on here about the 0300 code

i think i read you just...
Forum: Engine & Transmission
09-04-2010, 01:43 AM
Replies: 2
Views: 4,141
Posted By spkremer

to start out, try this check the spark plug...

to start out, try this
check the spark plug wires and the cap and rotor for any arcing or corrosion, also check the air filter
clean the throttle with "air intake cleaner" and a rag
replace the...
Forum: Engine & Transmission
09-04-2010, 01:35 AM
Replies: 8
Views: 1,455
Posted By spkremer

could be a crank sensor also when u get it...

could be a crank sensor
also when u get it running that code could be caused by a vacuum leak
Forum: 2nd Generation S-series (1995-2005) Tech
09-04-2010, 01:19 AM
Replies: 14
Views: 2,810
Posted By spkremer

0.74 is high, it should be less then or about...

0.74 is high, it should be less then or about 0.05, because of clock memory ,alarm, etc.., at this point start pulling out fuses and disconnecting any added accessories one by one, if you can't find...
Forum: 2nd Generation S-series (1995-2005) Tech
09-04-2010, 01:09 AM
Replies: 2
Views: 779
Posted By spkremer

bleed from where the master cylinder lines go...

bleed from where the master cylinder lines go into the abs unit( just crack the line loose like you were opening the bleeder valve)...then do the same with the lines coming out of the abs...
Forum: Engine & Transmission
09-04-2010, 12:08 AM
Replies: 33
Views: 5,044
Posted By spkremer

change the fuel filter, check fuel pressure ...

change the fuel filter, check fuel pressure

fuel pressure should be between 60 and 65 psi, but could be good as low as 55psi... the nozzle for the pressure tester is on the line goin to the spider...
Forum: Engine & Transmission
09-03-2010, 11:26 PM
Replies: 10
Views: 4,862
Posted By spkremer

nice!

nice!
Forum: 2nd Generation S-series (1995-2005) Tech
02-08-2010, 11:43 PM
Replies: 10
Views: 4,296
Posted By spkremer

try finding every ground point u can on the...

try finding every ground point u can on the engine and body, and clean em good. also look for broken wires or corroded wires along the engine wire harness.
corrosion adds resistance to the circuit...
Forum: Engine & Transmission
01-28-2010, 09:10 PM
Replies: 10
Views: 2,524
Posted By spkremer

I actually got a 98 4x4 blazer recently with a...

I actually got a 98 4x4 blazer recently with a few problems as well. Battery was draining within a few hours and it hardly ran. The battery problem ended up being the fuel system remaining on, after...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands