Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: bagnew
Showing results 1 to 8 of 8
Search took 0.00 seconds.
Forum: 2nd Generation S-series (1995-2005) Tech
03-14-2016, 02:59 PM
Replies: 5
Views: 1,638
Posted By bagnew

sounds like damp ignition parts mine does...

sounds like damp ignition parts

mine does the exact same thing i had trouble getting it started today wet weather and damp out all crank no fire.

took the dist cap off and dried it out along...
Forum: 2nd Generation S-series (1995-2005) Tech
03-14-2016, 02:35 PM
Replies: 17
Views: 2,210
Posted By bagnew

have you checked for dampness inside the...

have you checked for dampness inside the distributor?.

i almost forgot check the drive gear on the dist shaft if it is bad it will do things like that and give you fits and have you pulling out...
Forum: Paint, Body, & Interior
02-02-2015, 08:15 AM
Replies: 8
Views: 14,052
Posted By bagnew

i will do my drivers door hinge when it warms up...

i will do my drivers door hinge when it warms up out side so i can work on it.

pictures will be taken at every step so every one can see what i am saying.

as they say pictures are worth a...
Forum: Paint, Body, & Interior
02-02-2015, 08:00 AM
Replies: 8
Views: 14,052
Posted By bagnew

calipers work for measuring the bushing the knife...

calipers work for measuring the bushing the knife edge on the tips of the caliper is what i used one on each side of the bushing .

the copper slug was turned to .526 of an inch.
the...
Forum: Paint, Body, & Interior
02-02-2015, 07:24 AM
Replies: 8
Views: 13,574
Posted By bagnew

yes number 2 weld the holes but doing it the way...

yes number 2 weld the holes but doing it the way i am talking about means no drilling to get the hole back..

you are right about the cheesy bushing that they sell they are made to fail.

i used...
Forum: Paint, Body, & Interior
02-01-2015, 01:26 PM
Replies: 8
Views: 14,052
Posted By bagnew

this is what i fix my hinges with it works great...

this is what i fix my hinges with it works great i just stick it in the hole and weld the gap file the hole round if needed then put the bushing and pin in.

turn on a lath to get the same outside...
Forum: Paint, Body, & Interior
02-01-2015, 12:46 PM
Replies: 8
Views: 13,574
Posted By bagnew

you can turn a 5/8ths in copper rod to the size...

you can turn a 5/8ths in copper rod to the size of the bushing and then grind a flat spot on the side of it.

put it in the hole and use a wire welder to fill the gap then use a round file if...
Forum: Paint, Body, & Interior
02-01-2015, 12:23 PM
Replies: 18
Views: 8,398
Posted By bagnew

how i fixed my door hinge

i got a copper rod about 5/8 inch in diameter and turned it on a lath to the bushing size too both bushing sizes on the ends..

then then ground a flat on each end of it so it is round with a flat...
Showing results 1 to 8 of 8


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands