Blazer Forum - Chevy Blazer Forums - Search Results

Community
Search
Search: Posts Made By: matclark
Showing results 1 to 45 of 45
Search took 0.01 seconds.
07-26-2009, 08:52 PM
Replies: 17
Views: 3,588
Posted By matclark

my icm checked out fine....

my icm checked out fine....
07-15-2009, 11:42 AM
Replies: 17
Views: 3,588
Posted By matclark

2 weeks ago, today,,and yes, all ac delco from...

2 weeks ago, today,,and yes, all ac delco from the dealership...
07-14-2009, 10:48 PM
Replies: 17
Views: 3,588
Posted By matclark

didnt fix a thing !! still broke !! ...

didnt fix a thing !! still broke !!
cleaned/inspected and checked all voltages for map, tps, maf,,checked the power to distributor, and coil input/output, everything checked out fine,,,rechecked and...
07-13-2009, 11:38 PM
Replies: 17
Views: 3,588
Posted By matclark

ok,,tonight i was on the highway, going up a...

ok,,tonight i was on the highway, going up a steep hill, and as soon as i crested it, and let off the throttle peddle,it back fired through the intake really bad,,but then it drove good for about 10...
07-11-2009, 04:31 PM
Replies: 17
Views: 3,588
Posted By matclark

sorry to jump in on someone elses thread but i...

sorry to jump in on someone elses thread but i think we have the same thing going on and might be able to help each other,,,
i have the same issues, except mine doesnt stall out at a stop with...
04-19-2009, 03:57 PM
Replies: 11
Views: 2,887
Posted By matclark

i have always used 10w40, in every vehicle i have...

i have always used 10w40, in every vehicle i have ever owned. as for the bosch parts, the parts place said the plugs would be better, i do still have the old ac delco plugs and they look new, should...
04-10-2009, 11:21 PM
Replies: 11
Views: 2,887
Posted By matclark

sorry for new reply and not editing,but i thought...

sorry for new reply and not editing,but i thought i should just start this in a new box,
i am now getting a p0143 code once again...
i have replaced,,,
the trans, with a used unit that was...
04-05-2009, 04:04 PM
Replies: 1
Views: 3,792
Posted By matclark

tcc solenoid wiring??

how do you unwire the tcc solenoid? mine does not have a connector, its wired directly into/through the wiring harness. this is the same on both,1 piece case and a 2 piece 4l60e's i have. do you have...
03-26-2009, 01:00 AM
Replies: 16
Views: 2,816
Posted By matclark

i still think its your grounds,,,found all mine...

i still think its your grounds,,,found all mine and cleaned them, now the voltage is back up
02-23-2009, 12:06 PM
Replies: 9
Views: 11,422
Posted By matclark

RE: what tranny fits my blazer?

i just tried on my 96 blazer 4x4, conclusion is that the 1 piece 4l60e, will NOT interchange with the 2 piece 4l60e, that has the removable bell housing. the transfer case adaptor will not...
02-22-2009, 02:29 AM
Replies: 8
Views: 1,503
Posted By matclark

RE: coolant in number 4 cylinder

sorry it took so long to finish the post,, it was the head gaskets for sure,,the heads were nice and flat only 1-2 thous out, not bad at all,,, i took them to my shop and milled10 thous off of both,...
02-22-2009, 02:20 AM
Replies: 12
Views: 2,356
Posted By matclark

RE: Weird tranny problem???

depends on the year and the 8th digit of the vin....tp= throttle position sensor, the forums also told me to check/clean all thepcm grounds, i found the main pcm ground on the top of theframe, near...
02-21-2009, 10:24 PM
Replies: 9
Views: 11,422
Posted By matclark

RE: what tranny fits my blazer?

so if i have a 4l60e with a torque convertor dust cover, will it interchange with a 4l60e that has the full alum. bell housing? both are out of 96 blazers.
02-21-2009, 10:01 PM
Replies: 12
Views: 2,356
Posted By matclark

RE: Weird tranny problem???

the fluid is burnt, ok, it cant hurt to change it, if theres damage then its already happened, it just goingto get worsebut, no pwer at higher gears/speeds....tp sensor? shift solenoid? clogged valve...
Forum: General Chat
02-18-2009, 05:30 PM
Replies: 420
Views: 82,250
Posted By matclark

RE: Official MPG Poll

my 94 gets 12.6, and my 96 gets 15.6,
i drive 25 miles a day to work, 90% highway, very mountainous!!
Forum: General Chat
02-18-2009, 05:19 PM
Replies: 0
Views: 451
Posted By matclark

setting up for trans removal?

how does everyone set up there blazers to replace the tranny? i have never replaced a trans in a blazerbefore, normally i would only raise the front on the vehicle. should i consider raising up all 4...
Forum: General Chat
02-18-2009, 05:07 PM
Replies: 244
Views: 180,849
Posted By matclark

RE: A list of common annoying S-10 Blazer quirks.

list of my quirks:
my 94 blazer 4.3 w 4x4 175,000miles,,,,ball joints, a-arm bushings, drag link, pitman arm, head gaskets, transmission, horn button wire, heater controls, many tranfer case...
02-13-2009, 05:56 PM
Replies: 9
Views: 5,931
Posted By matclark

RE: 96 Blazer transmission problems

i asked in another post and got no response,,so i will ask here also,,,does anyone have the transmission wiring diagram for the 96 s10 blazer 4l60e? i need to verify that i am getting power to my...
02-10-2009, 08:29 PM
Replies: 11
Views: 2,887
Posted By matclark

RE: 96 blazer transmision prob

sorry,,,i forgot to say, its stuck in first now, the new tps didnt help a thing,it got worse !....earlier i had posted in the wrong spot, sorry ,about testing the tps, heres what i got with a new and...
02-10-2009, 06:55 PM
Replies: 11
Views: 2,887
Posted By matclark

RE: 96 blazer transmision prob

i almost forgot, the cruise control quit working at about the same time
02-10-2009, 06:08 PM
Replies: 11
Views: 2,887
Posted By matclark

RE: 96 blazer transmision prob

replaced the tps, cleaned all the grounds i could find under the hood, with the positive cable unhooked on thebattery, checked the maf, it was clean, all the vaccuum lines looked real...
02-10-2009, 11:47 AM
Replies: 11
Views: 2,887
Posted By matclark

RE: 96 blazer transmision prob

ok,,i got the codes read, they also ran the trans by the computer and all the solenoids are working properly.
the codes are:
po134 bank 1 sensor 1
po135 bank 1 sensor 1
po143 bank 1...
02-10-2009, 08:18 AM
Replies: 11
Views: 2,887
Posted By matclark

RE: 96 blazer transmision prob

itjust started all at once,the first time,i was on my way home from work, i got off the highway,went to take offfrom the exit rampand noticed it wasnt shifting out of 1, then when i let off the...
02-10-2009, 08:13 AM
Replies: 11
Views: 2,887
Posted By matclark

RE: 96 blazer transmision prob

yes i do still have reverse, engages nice and smooth with no noises at all, 4x4 hi and lo,engages perfectly also
02-09-2009, 10:58 PM
Replies: 11
Views: 2,887
Posted By matclark

96 blazer transmision prob

sorry but i didnt know where to post this to...i have a 96 s10 blazer 4.3 4x4,,,transmission started acting up, leaving me with first and forth only,,after reading many posts on here,,i replaced the...
02-08-2009, 06:17 PM
Replies: 30
Views: 17,330
Posted By matclark

RE: hesitation/hiccup/bucking @ 2k rpm.. ideas?

on a 96 s10 4.3 4x4 blazer,how do you test the tps? there are three wires, black, blue and grey,,which is which? i probed the wires and hooked up my digi mult meter,, key on and engine off,,,,,here...
12-08-2008, 04:44 PM
Replies: 4
Views: 1,863
Posted By matclark

OBD I contact ?!?!?

sorry to bother you, but i need some help! how do i check the tccm codes with a obd1 12 pin connector? or can i?
i have a 1994 s10 blazer4x4, i can not get it to go into 4hi. i can hear the tccm...
10-18-2008, 10:14 AM
Replies: 2
Views: 1,151
Posted By matclark

RE: heater control vaccuum switch

sorry its a 1994 s-10 blazer 4.3w.....i have now replaced the vaccuum switch twice,,,both switches are hissing,,,i guess they dont make a vac switch that works...they all leak ! am i getting to much...
10-17-2008, 01:10 PM
Replies: 2
Views: 1,151
Posted By matclark

heater control vaccuum switch

does anyone know how many vaccuum lines go to the vaccuum switch on the heater controls? i have a black, grey, green, tan or brown, an orange, and then a blank/empty slot on the connector to the...
07-02-2008, 10:22 PM
Replies: 2
Views: 5,350
Posted By matclark

distributor cap bolts stripped

i have a 94 s-10 blazer 4.3L,,,,,when i replaced the dist. cap, the bolts stripped the threads out of the dist.....i have tried the old bolts and they just keep spinning. any ideas on how to fix...
06-29-2008, 06:45 PM
Replies: 5
Views: 2,607
Posted By matclark

RE: how to test transfer case vaccuum switch

i know where the hoses come from, for the tc vac switch.....i need to know which one on the vaccuum switch itself, does what,,,onthe switch itself which one is the vent ? which one is the source from...
06-29-2008, 11:34 AM
Replies: 5
Views: 2,607
Posted By matclark

RE: how to test transfer case vaccuum switch

which 1 of the 3nipples is the vent? the other 2 should be the vaccuum switch,from the engine to the front actuator...
06-29-2008, 11:31 AM
Replies: 5
Views: 2,607
Posted By matclark

RE: how to test transfer case vaccuum switch

to simplify things...i need a break down of the transfer case vaccuum switch....which one of the 3 nipples does what??
06-29-2008, 11:29 AM
Replies: 2
Views: 1,696
Posted By matclark

RE: 4.3 vaccuum diagram,please help !!!

i really dont think its normal for the vaccuum ball to be unhooked,,,the heater to be unhooked,the cruize control to be unhooked, and the front actuator to be hooked up directly to the engine....the...
06-28-2008, 10:15 PM
Replies: 5
Views: 2,607
Posted By matclark

how to test transfer case vaccuum switch

how would you test the transfer case vaccuum switch on a 94 4.3 s-10 blazer ? i need to know,,on the switch itself,,,which one of the 3 comes from the engine,, and which 1 goes to front actuator,,and...
06-28-2008, 03:46 PM
Replies: 2
Views: 1,696
Posted By matclark

4.3 vaccuum diagram,please help !!!

i have purchused a 1994 s-10 blazer 4x4 4.3.....i have had all kinds of trouble with this thing and i am about ready to sell......but i cant be beat....the vaccuum is all messed up,,i bought a haynes...
05-28-2008, 12:41 AM
Replies: 1
Views: 1,114
Posted By matclark

spark knock

i have a '94 4.3 blazer,,fixing head gaskets now,,,i bought it and drove it home it ran fine,, took it out later that day andit started spark knocking really bad,i tried messing with the timing and i...
05-27-2008, 10:20 PM
Replies: 1
Views: 1,454
Posted By matclark

power steering pulley tool

i have a '94 4.3 blazer,,,i live in the middle of no where,,andno one locally hasthe proper tool for the removal of the power steering pump pulley ,,,,does anyone know anyway to get the pulley off...
05-27-2008, 09:25 PM
Replies: 8
Views: 1,503
Posted By matclark

RE: coolant in number 4 cylinder

ok,,the right head gasket is gone,,,problem found,,thanks guys.....next question....i dont have the power sterring pulley puller tool,,,so i cant get the left head off,,,the compression test showed...
05-27-2008, 03:57 AM
Replies: 8
Views: 1,503
Posted By matclark

RE: coolant in number 4 cylinder

how bad do the heads warp on the 4.3? is it a givin' that they be machined?
05-27-2008, 02:33 AM
Replies: 8
Views: 1,503
Posted By matclark

coolant in number 4 cylinder

ibought an 94 4.3 blazer,i brougth it home with no problems, loaded thefamily in it andwent for a ride, it started to spark knock, i brougth it home checked the timing and all was good, we went back...
05-15-2008, 10:35 AM
Replies: 4
Views: 601
Posted By matclark

RE: is this a good deal?

cool,,thanks alot...if i dont end up buying it i will let you all know where it is. i have found a 91,92,93, and a 94,all seem fair but the 92, has the lowest miles. i will say this,they are in va...
05-14-2008, 03:48 PM
Replies: 4
Views: 601
Posted By matclark

is this a good deal?

i need to know if this is a good deal,,and what to look for,,and what to ask about it. i found an 1992 s10 blazer 4x4, 4 door,72,000miles, 4.3 vortec,4 new tires,good inspection, nothing wrong, ac...
05-13-2008, 10:37 PM
Replies: 6
Views: 729
Posted By matclark

what to look for

hi, i am new to the s10 blazers. i looking to purchase a 91-94,,,what should i be looking out for? what things could be problems? etc...
05-13-2008, 10:30 PM
Replies: 4
Views: 467
Posted By matclark

what to look out for

hi everyone, i am new to the s10 blazers,,i am looking to buy a 91-94, preferably the 94. but i need to know what should i be looking for, good and bad... what could i look for that might be a...
Showing results 1 to 45 of 45


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands