Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: Cerpindicular
Showing results 1 to 15 of 15
Search took 0.00 seconds.
Forum: 2nd Generation S-series (1995-2005) Tech
07-25-2011, 11:13 PM
Replies: 1
Views: 1,627
Posted By Cerpindicular

best way to fix 1996 blazers rotted brake line

one of the metal lines (can't see which one) running across the top of my frame rail has rusted through right behind the body mount area where the frame angles back up in the wheel well. I am having...
Forum: 2nd Generation S-series (1995-2005) Tech
07-18-2011, 02:15 AM
Replies: 10
Views: 4,832
Posted By Cerpindicular

yeah its going to have to stay zip tied for a bit...

yeah its going to have to stay zip tied for a bit till i have the extra money for a billet dizzy for it. And everyone loves moonshine :P
Forum: 2nd Generation S-series (1995-2005) Tech
07-14-2011, 02:11 AM
Replies: 4
Views: 4,045
Posted By Cerpindicular

guess i can just pull out of the other skid plate...

guess i can just pull out of the other skid plate and see if it works and if it does go match it up
Forum: 2nd Generation S-series (1995-2005) Tech
07-13-2011, 02:28 PM
Replies: 4
Views: 4,045
Posted By Cerpindicular

96 blazer 4wd front skid plate question

anyone know the bolt size that holds the front skid under the oil pan on. does it use the same size as the one under the trans? My bolts i guess came loose and dropped the skid in the middle of the...
Forum: 2nd Generation S-series (1995-2005) Tech
07-10-2011, 06:02 PM
Replies: 10
Views: 4,832
Posted By Cerpindicular

96 4.3 blazer distributor cap problem

Some one at some point (probably when the swapped the engine into the rig) busted the hole that one of my screws for tightening down the distributor cap (bumped it while trouble shooting a miss think...
Forum: 2nd Generation S-series (1995-2005) Tech
06-27-2011, 05:15 PM
Replies: 1
Views: 1,305
Posted By Cerpindicular

So my 96 (97 or 98 engine) blazer is annoying me...

So my 96 (97 or 98 engine) blazer is annoying me at the moment. Runs fine and makes plenty of power when cold and runs fine (no sputtering or dieing) when warm but it just seems to lack horribly in...
Forum: 1st Generation S-series (1983-1994) Tech
04-23-2011, 11:33 AM
Replies: 5
Views: 3,406
Posted By Cerpindicular

hmmmm ran the vin and it comes up as a 96 not a...

hmmmm ran the vin and it comes up as a 96 not a 95....still work for a drop in with my intake on it? well late 95 anywayz
Forum: 1st Generation S-series (1983-1994) Tech
04-17-2011, 03:15 PM
Replies: 5
Views: 3,406
Posted By Cerpindicular

sucks its a 95 the body panels doors and glass -...

sucks its a 95 the body panels doors and glass - the windshield are all good.
Forum: 1st Generation S-series (1983-1994) Tech
04-17-2011, 03:05 PM
Replies: 5
Views: 3,406
Posted By Cerpindicular

yeah the dizzy is different. Is there any parts...

yeah the dizzy is different. Is there any parts that would be good to grab that will bolt? Axles, gas tank, seats? The 95 is all leather with electronic seats though.
Forum: 1st Generation S-series (1983-1994) Tech
04-17-2011, 12:03 PM
Replies: 5
Views: 3,406
Posted By Cerpindicular

parts compatibility question

So i blew up a engine i just swapped into our 94 blazer 4x4. I picked up a 95 with a newer/rebuilt engine in it for cheap and it also has a good trans tcase axles and what not. The plan is to swap...
Forum: 1st Generation S-series (1983-1994) Tech
03-04-2011, 11:29 PM
Replies: 8
Views: 3,762
Posted By Cerpindicular

I tore the intake off today (dizzy turns fine)...

I tore the intake off today (dizzy turns fine) checked the balance shaft and while there was front to back play it was small enough i just wrote it off as normal. I did run it for a few seconds with...
Forum: 1st Generation S-series (1983-1994) Tech
03-04-2011, 03:48 PM
Replies: 8
Views: 3,762
Posted By Cerpindicular

how about if i pull the gear that drives the...

how about if i pull the gear that drives the balance shaft and pull the shaft out to eliminate it?
Forum: 1st Generation S-series (1983-1994) Tech
03-04-2011, 01:07 PM
Replies: 8
Views: 3,762
Posted By Cerpindicular

sounds to be on the passenger side top to middle...

sounds to be on the passenger side top to middle of the block...Kind of hoping it is the balance shaft bearing gone out for the squelling and allowing the shaft to bounce around for the...
Forum: 1st Generation S-series (1983-1994) Tech
03-04-2011, 12:25 PM
Replies: 8
Views: 3,762
Posted By Cerpindicular

is it possible on mine that its a bad balance...

is it possible on mine that its a bad balance shaft?
Forum: 1st Generation S-series (1983-1994) Tech
03-03-2011, 08:09 PM
Replies: 8
Views: 3,762
Posted By Cerpindicular

94 s10 blazer vortec 4.3l knock miss and squel

first time posting so hi everyone. As the title says it knocks it squels and has miss and is making bad power. was told burnt valve but i dont know. Did find a youtube on a blazer doing pretty...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands