Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: kermit1112
Showing results 1 to 12 of 12
Search took 0.00 seconds.
Forum: 2nd Generation S-series (1995-2005) Tech
01-21-2010, 11:20 AM
Replies: 20
Views: 6,890
Posted By kermit1112

no bent pins also put new crank sensor in still...

no bent pins also put new crank sensor in still misfiring dont know what to do now?
Forum: 2nd Generation S-series (1995-2005) Tech
01-20-2010, 01:15 PM
Replies: 6
Views: 816
Posted By kermit1112

what was the code for coil wire?

what was the code for coil wire?
Forum: 2nd Generation S-series (1995-2005) Tech
01-20-2010, 12:06 PM
Replies: 20
Views: 6,890
Posted By kermit1112

is that the main harness wth all the pins. or is...

is that the main harness wth all the pins. or is where the fuel lines go into manifold?
Forum: 2nd Generation S-series (1995-2005) Tech
01-20-2010, 11:47 AM
Replies: 20
Views: 6,890
Posted By kermit1112

how do you check the pins on spider?

how do you check the pins on spider?
Forum: 2nd Generation S-series (1995-2005) Tech
01-19-2010, 09:34 PM
Replies: 20
Views: 6,890
Posted By kermit1112

ok sorry didnt know they were links. thxs

ok sorry didnt know they were links. thxs
Forum: 2nd Generation S-series (1995-2005) Tech
01-19-2010, 09:09 PM
Replies: 20
Views: 6,890
Posted By kermit1112

yeah i know what they are. but i just did tune up...

yeah i know what they are. but i just did tune up and replaced ign module coil and checked every vacuum line and sensors. but still has miss?
Forum: 2nd Generation S-series (1995-2005) Tech
01-19-2010, 08:28 PM
Replies: 20
Views: 6,890
Posted By kermit1112

got truck scan for codes, and have 2 of them and...

got truck scan for codes, and have 2 of them and they are po155 n po300. i just finished doing a complete tune up and truck still has a miss. need help bad.
Forum: 2nd Generation S-series (1995-2005) Tech
01-19-2010, 11:18 AM
Replies: 20
Views: 6,890
Posted By kermit1112

did you do your intake to? and did this happen?

did you do your intake to? and did this happen?
Forum: 2nd Generation S-series (1995-2005) Tech
01-19-2010, 10:59 AM
Replies: 20
Views: 6,890
Posted By kermit1112

i also replace ign module to because went bad a...

i also replace ign module to because went bad a couple weeks ago. wondering if coil is bad to, because when i give it some gas in higher rpms it smooth out.
Forum: 2nd Generation S-series (1995-2005) Tech
01-19-2010, 10:44 AM
Replies: 20
Views: 6,890
Posted By kermit1112

i just check all the wires and check for vacuum...

i just check all the wires and check for vacuum leaks and there is nothing.could it be a bad dist cap and rotor? i dont have a scanner to scan the code either. i only did lower gasket because thats...
Forum: 2nd Generation S-series (1995-2005) Tech
01-19-2010, 08:10 AM
Replies: 20
Views: 6,890
Posted By kermit1112

dist in right mark rotor and dist housing to make...

dist in right mark rotor and dist housing to make sure it was.also all plug are in right spots triple check eveything. i will find out code today.

when you say intake pelnum what do you mean? i...
Forum: 2nd Generation S-series (1995-2005) Tech
01-18-2010, 09:22 PM
Replies: 20
Views: 6,890
Posted By kermit1112

HELP! Replaced intake manifold gasket - have problems now.

I just replaced my intake manifold gasket and MAP sensor on my 2000 Blazer. I put it all back together as per the directions. I started my truck and the engine has a miss. The check engine light is...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands