Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: Extracrucial
Showing results 1 to 13 of 13
Search took 0.00 seconds.
Forum: General Chat
01-31-2021, 11:11 PM
Replies: 4
Views: 357
Posted By Extracrucial

33s on 2.5lift, wheel spacers?

I’m installing 33/12.50R15s on my 2000 blazer LS 4x4 two door, it’s running 31s now without rubbing, the rims are 15x8s black bullet holes with beadlock trim. My question is should I invest in a...
Forum: 2nd Generation S-series (1995-2005) Tech
12-15-2020, 09:47 PM
Replies: 15
Views: 704
Posted By Extracrucial

im working on getting a scanner , but to the...

im working on getting a scanner , but to the story,..
i had done a lot of work to this blazer and was trying to achieve 0codes with no check engine light,well i achieved 0codes but random misfire...
Forum: 2nd Generation S-series (1995-2005) Tech
12-15-2020, 04:44 PM
Replies: 1
Views: 282
Posted By Extracrucial

EDI distributor installed incorrectly?

So far as an EDI distributor is it possible that it can be put in not exactly right and the vehicle still run just poorly? a vehicle cannot run if its on the exhaust stroke can it? i understand the...
Forum: 2nd Generation S-series (1995-2005) Tech
12-15-2020, 04:33 PM
Replies: 4
Views: 1,266
Posted By Extracrucial

im guessing the rotor is good?your problem...

im guessing the rotor is good?your problem sounds similar to mine atm- im currently trying to get my 2000 blazer 4.3 running right after replacing distributor so if you fixed your issues please...
Forum: 2nd Generation S-series (1995-2005) Tech
12-15-2020, 04:27 PM
Replies: 15
Views: 704
Posted By Extracrucial

no question is stupid, but i checked my plug...

no question is stupid, but i checked my plug wires and i found two that needed to be switched, i corrected them & the backfire nearly stopped but its still slow responding to the throttle & im scared...
Forum: 2nd Generation S-series (1995-2005) Tech
12-15-2020, 04:18 PM
Replies: 15
Views: 704
Posted By Extracrucial

i swapped my scanner for a 50inch lightbar about...

i swapped my scanner for a 50inch lightbar about a week before this happened 😰
but what are the chances i jumped timing? because i really don’t want to take apart my motor i just hit 100,000......
Forum: 2nd Generation S-series (1995-2005) Tech
12-15-2020, 12:32 PM
Replies: 15
Views: 704
Posted By Extracrucial

so i got my blazer started , and drove it home to...

so i got my blazer started , and drove it home to so itd at least be here, but it’s misfiring, backfiring , the rotor on the distributer is new and the distributor itself is nearly new,the caps good...
Forum: 2nd Generation S-series (1995-2005) Tech
12-14-2020, 03:32 PM
Replies: 15
Views: 704
Posted By Extracrucial

ah this is definitely handy thanks!!😌

ah this is definitely handy thanks!!😌
Forum: 2nd Generation S-series (1995-2005) Tech
12-14-2020, 03:32 PM
Replies: 15
Views: 704
Posted By Extracrucial

thanks! im having to jump it off every time im...

thanks! im having to jump it off every time im ready to start it on top of it being in a buddys driveway and not home , im hoping the next time i get to it i can get it right, im going to sell my...
Forum: 2nd Generation S-series (1995-2005) Tech
12-12-2020, 08:35 PM
Replies: 2
Views: 557
Posted By Extracrucial

sorry I didn’t think anyone would reply I found...

sorry I didn’t think anyone would reply I found the issue! It was a star screw that is in the front of the throttle body to the left it was pushing the throttle from being screwed in too far I backed...
Forum: 2nd Generation S-series (1995-2005) Tech
12-12-2020, 08:27 PM
Replies: 15
Views: 704
Posted By Extracrucial

2nd gen rotor alignment?! 6or#1cylinder??

I have tried getting my 2000 blazer Ls 4x4 started for two weeks now, I took out the old Distributor bc I was fixing all issues and trying to have it show “0” when scanned, I got to the point where...
Forum: 2nd Generation S-series (1995-2005) Tech
10-06-2020, 12:26 AM
Replies: 2
Views: 557
Posted By Extracrucial

2000 blazer 4.3 very high idle after attempting cold air intake assembly

Hi my 2000 blazer 4.3 4x4, 2Door LS started idling when starting cold or hot at about 2500rpm I couldn’t mount my new spectre cold air intake because of a stripped nut I need off to put the screw...
Forum: General Chat
10-05-2020, 11:09 PM
Replies: 0
Views: 24
Posted By Extracrucial

2000 Blazer 4.3, 2Door 4x4, VERY high idle after trying to install cold air intake

Hi, my 2000 blazer 4.3 two door 4x4 was idling fine before I tried to install a cold air intake by spectre, the piece that mounts to the top of the throttle body has a space that requires higher up...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands