Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
 
Page 1 of 4
1
2
3
Last »
Search: Posts Made By: burning_soul07
Showing results 1 to 50 of 158
Search took 0.01 seconds.
Forum: 1st Generation S-series (1983-1994) Tech
05-02-2012, 06:45 PM
Replies: 7
Views: 9,005
Posted By burning_soul07

Has to be a bad connection by your blower motor....

Has to be a bad connection by your blower motor. Lift the hood and check the area by the firewall and passenger side. There should be a 6? pin wire clip going in to the right of the blower motor,...
Forum: 1st Generation S-series (1983-1994) Tech
04-24-2012, 10:06 PM
Replies: 14
Views: 1,834
Posted By burning_soul07

From what I know the transmission has a vaccuum...

From what I know the transmission has a vaccuum line going to it that reads the pressure. This pressure determines when the shift points are. If the vaccuum line is old and leaking maybe it isn't...
Forum: 1st Generation S-series (1983-1994) Tech
02-28-2012, 10:13 PM
Replies: 6
Views: 891
Posted By burning_soul07

Fuel Pump Positive jumper wire to test if the...

Fuel Pump Positive jumper wire to test if the fuel pump is working. 100% sure!!
Forum: 1st Generation S-series (1983-1994) Tech
01-14-2012, 10:32 PM
Replies: 4
Views: 2,555
Posted By burning_soul07

Create an account at autozone.com and then enter...

Create an account at autozone.com and then enter your vehicle information and then use the search to search vacuum diagram, it will give you results to go off of. Good luck.
Forum: 1st Generation S-series (1983-1994) Tech
01-04-2012, 12:23 AM
Replies: 16
Views: 21,464
Posted By burning_soul07

I had this same problem with my same year Blazer...

I had this same problem with my same year Blazer same engine. It actually came out to be the gap was too close on the spark plugs causing a premature spark before the valve's were closed causing a...
Forum: 1st Generation S-series (1983-1994) Tech
12-29-2011, 08:03 PM
Replies: 3
Views: 1,286
Posted By burning_soul07

Considering you said spider I am guessing your...

Considering you said spider I am guessing your working on a CPI. I would suggest definately the fuel filter. Then check the fuel pressure at the manifold and also do a leak down test (search about it...
Forum: 1st Generation S-series (1983-1994) Tech
12-08-2011, 09:19 PM
Replies: 9
Views: 2,032
Posted By burning_soul07

I had the same problem. Mine was the gap on the...

I had the same problem. Mine was the gap on the spark plugs was too close causing premature fire and popping out the TBI.
Forum: 1st Generation S-series (1983-1994) Tech
12-05-2011, 06:18 PM
Replies: 18
Views: 12,276
Posted By burning_soul07

I also did the heater core in mine last year. I...

I also did the heater core in mine last year. I removed a few of the bolts on the dash like a write up had said. I would say the most difficult part is getting it back into the right spot exactly so...
Forum: 1st Generation S-series (1983-1994) Tech
11-29-2011, 06:04 PM
Replies: 60
Views: 4,738
Posted By burning_soul07

I had this same problem. Had to make a new...

I had this same problem. Had to make a new connection to the window at the passenger side. Then had to track down where I had a bad connection. My bad connection was where the wire screwed into the...
Forum: 1st Generation S-series (1983-1994) Tech
11-17-2011, 08:44 PM
Replies: 2
Views: 678
Posted By burning_soul07

I would check the wiring going from the encoder...

I would check the wiring going from the encoder motor to the 4x4 computer. It seems like the computer is not getting signal from the encoder when it hits 4hi telling it to stop.
Forum: 1st Generation S-series (1983-1994) Tech
11-08-2011, 07:41 PM
Replies: 16
Views: 11,234
Posted By burning_soul07

To check what swartltt said about the vacuum...

To check what swartltt said about the vacuum getting to the line. With the battery out like you said, pull the vacuum line off the actuator and with the 4x4 switch on 4 lo or high cover the line with...
Forum: 1st Generation S-series (1983-1994) Tech
11-07-2011, 07:15 PM
Replies: 16
Views: 1,666
Posted By burning_soul07

If it is "horribly out of time" make sure you got...

If it is "horribly out of time" make sure you got the plug wires in the right way. The #1 starts on the oppisite side of the block on the 2.8L compared to normal chevys. And 1 starts on the...
Forum: 1st Generation S-series (1983-1994) Tech
11-03-2011, 07:38 PM
Replies: 11
Views: 5,506
Posted By burning_soul07

Thats the answer. With pics. Good job Swartlkk...

Thats the answer. With pics. Good job Swartlkk your brain is a Blazers best friend.
Forum: 1st Generation S-series (1983-1994) Tech
11-03-2011, 05:50 PM
Replies: 11
Views: 5,506
Posted By burning_soul07

I can picture that, but never have dug that deep....

I can picture that, but never have dug that deep. Hopefully someone else can chime in here and offer some been there done that advice.

Nothing around the actuator had been bent? Maybe if you find...
Forum: 1st Generation S-series (1983-1994) Tech
11-03-2011, 05:24 PM
Replies: 11
Views: 5,506
Posted By burning_soul07

Wow thats a lot of work.

Stupid easy question: Does the vacuum actuator pull the cable all the way so the coupling is fully engaged? I have heard of times when this area sticks and only engages the front axle half way making...
Forum: 1st Generation S-series (1983-1994) Tech
10-21-2011, 10:34 AM
Replies: 16
Views: 1,666
Posted By burning_soul07

Start by having someone crank the engine with the...

Start by having someone crank the engine with the top of the aircleaner open and check to see if there is fuel coming out of the 2 jets pointing down into the intake.yes or no.
Forum: 1st Generation S-series (1983-1994) Tech
10-20-2011, 07:25 PM
Replies: 16
Views: 1,666
Posted By burning_soul07

There is a jumper on the firewall directly behind...

There is a jumper on the firewall directly behind the throttle body and air cleaner, it is a single wire clip. Jump this wire to the 12V positive there. If no fuel during starting out of the jets...
Forum: 1st Generation S-series (1983-1994) Tech
10-19-2011, 08:51 PM
Replies: 8
Views: 2,343
Posted By burning_soul07

Basically this one line your talking about should...

Basically this one line your talking about should come out of the intake monifold and go to a "T" fitting. At this fitting it will go to multiple things. The "T" should have a line going down to the...
Forum: 1st Generation S-series (1983-1994) Tech
10-14-2011, 10:47 AM
Replies: 7
Views: 7,535
Posted By burning_soul07

I opened mine in the middle and only removed the...

I opened mine in the middle and only removed the bolts around the thing that were easy to get to. I pulled it strait up after cutting the lines that go to it off so it would come out. At least...
Forum: 1st Generation S-series (1983-1994) Tech
10-13-2011, 09:37 PM
Replies: 7
Views: 7,535
Posted By burning_soul07

I removed all my ac guts in the engine and in the...

I removed all my ac guts in the engine and in the box then just HVAC taped over it. I'm not sure about the wiring. I bet my hole wasnt as big as yours though. Why the problem with the heater core,...
Forum: 1st Generation S-series (1983-1994) Tech
10-03-2011, 04:32 PM
Replies: 28
Views: 4,037
Posted By burning_soul07

Hows about the bushings on the upper control arm?...

Hows about the bushings on the upper control arm? Other then that I would thing the spindle itself. Question: Does the truck have vibrations or the (Front drivers side) tire just wobble at highway...
Forum: 1st Generation S-series (1983-1994) Tech
06-04-2011, 05:14 PM
Replies: 1
Views: 3,639
Posted By burning_soul07

I have my charcoal canistor hooked directly up to...

I have my charcoal canistor hooked directly up to the throttle body. There is a 2 port "ported vacuum switch" on the intake area by the thermostat that is suppose to apply vacuum to the canister when...
Forum: 1st Generation S-series (1983-1994) Tech
06-01-2011, 09:04 PM
Replies: 2
Views: 2,035
Posted By burning_soul07

It is my best knowledge that you dont want to...

It is my best knowledge that you dont want to stop in N on the floor shifter. You must make these moves from 4hi to 4lo and back with one fast smooth motion ortherwise I know it will grind. It says...
Forum: 1st Generation S-series (1983-1994) Tech
05-31-2011, 10:21 PM
Replies: 14
Views: 6,557
Posted By burning_soul07

Right behind the kick panel in the center on mine...

Right behind the kick panel in the center on mine there is a little metal switch that goes back and forth. It switches floor on and off. Take the kick panel off and youll see it.
Forum: 1st Generation S-series (1983-1994) Tech
05-31-2011, 10:17 PM
Replies: 3
Views: 11,546
Posted By burning_soul07

Has your system been converted to R134a? If so I...

Has your system been converted to R134a? If so I think it is about 2 lbs. My system has been converted and there is a little sticker in there that says how much.
Forum: 1st Generation S-series (1983-1994) Tech
05-26-2011, 09:24 PM
Replies: 2
Views: 1,810
Posted By burning_soul07

When timing, did you unplug the wire under the...

When timing, did you unplug the wire under the carpet on the floor passengers side? You must do this or it will not read properly.
Forum: 1st Generation S-series (1983-1994) Tech
05-23-2011, 10:05 PM
Replies: 8
Views: 2,474
Posted By burning_soul07

see the link in my signature

see the link in my signature
Forum: 1st Generation S-series (1983-1994) Tech
05-20-2011, 08:21 PM
Replies: 2
Views: 2,496
Posted By burning_soul07

The round thing is the vacuum storage container....

The round thing is the vacuum storage container. It should be hooked up. Also, on my 2.8, the Charcoal canister is hooked up to a ported vacuum switch, but I have mine ran strait to the engine and...
Forum: 1st Generation S-series (1983-1994) Tech
05-19-2011, 06:31 PM
Replies: 5
Views: 1,932
Posted By burning_soul07

The sensor is positioned at the spot on the gear...

The sensor is positioned at the spot on the gear selector where the light comes on. LOL... I remember, at an oil place..... "sir, your brake lights don't work" So I got in and turned them on (mine...
Forum: 1st Generation S-series (1983-1994) Tech
05-14-2011, 08:07 PM
Replies: 3
Views: 962
Posted By burning_soul07

Find some different injectors from a pull yard or...

Find some different injectors from a pull yard or ebay<-(perfeered source for reman ones) and try those. Who knows what was in that box.
Forum: 1st Generation S-series (1983-1994) Tech
04-02-2011, 06:56 PM
Replies: 26
Views: 10,496
Posted By burning_soul07

I was just at my local u pull it yesterday, and...

I was just at my local u pull it yesterday, and every Blazer with a Vortes had the cover off and the parts out of it. People must wait in line for these things. Glad I dont have one on my TBi.
Forum: 1st Generation S-series (1983-1994) Tech
04-02-2011, 06:31 PM
Replies: 14
Views: 3,953
Posted By burning_soul07

All these replys are right. It does suck and its...

All these replys are right. It does suck and its a hassle. I tried 4 times b4 mine stayed. The "wings" on the channel guide need to be expanded or spread open so they go into the guide and stay...
Forum: 1st Generation S-series (1983-1994) Tech
04-01-2011, 07:31 PM
Replies: 14
Views: 3,953
Posted By burning_soul07

I had to super glue and clamp my guides in place...

I had to super glue and clamp my guides in place because the clip in the center never clipped.
Forum: 1st Generation S-series (1983-1994) Tech
03-30-2011, 08:43 PM
Replies: 4
Views: 9,727
Posted By burning_soul07

The wheel speed sensors may be losing track of...

The wheel speed sensors may be losing track of the teeth. Try to clean your wheel speed sensors and also the gears that it senses.
Forum: 1st Generation S-series (1983-1994) Tech
03-30-2011, 06:19 PM
Replies: 2
Views: 622
Posted By burning_soul07

If you could please update your signature...

If you could please update your signature information with year and engine that would be very helpful.
Forum: 1st Generation S-series (1983-1994) Tech
03-30-2011, 06:16 PM
Replies: 7
Views: 710
Posted By burning_soul07

All great ideas. Searching is your best bet. For...

All great ideas. Searching is your best bet. For any extra info on the vacuum check the link in my signature on my post here about the vacuum. Also, you must be in neutral and stopped, with the...
Forum: 1st Generation S-series (1983-1994) Tech
03-29-2011, 06:40 PM
Replies: 20
Views: 36,879
Posted By burning_soul07

Both of you might want to check the ground...

Both of you might want to check the ground connection to the frame coming off the battery. Make sure the connection is clean at poth points and the wire is not corroded.
Forum: 1st Generation S-series (1983-1994) Tech
03-28-2011, 10:56 PM
Replies: 20
Views: 36,879
Posted By burning_soul07

Sounds like you might have some crossed wires....

Sounds like you might have some crossed wires. For the parking lights, pull fuses til you find which fuse its on to trace the wires that way. Also, on Autozone.com there is wiring diagrams that could...
Forum: 1st Generation S-series (1983-1994) Tech
03-28-2011, 06:09 PM
Replies: 3
Views: 1,081
Posted By burning_soul07

Read my link in my signature about the 4x4.

Read my link in my signature about the 4x4.
Forum: 1st Generation S-series (1983-1994) Tech
03-28-2011, 12:09 AM
Replies: 7
Views: 835
Posted By burning_soul07

You know, I was wondering about that tooooo....

You know, I was wondering about that tooooo. Could I just put the leafs on top of the axle or do I got to get shackels? I am sure they sell shackels, which extend the ends of the leaves to the frame...
Forum: 1st Generation S-series (1983-1994) Tech
03-27-2011, 01:20 PM
Replies: 7
Views: 3,619
Posted By burning_soul07

I'd say just a friek thing. Most likely the...

I'd say just a friek thing. Most likely the solenoid got stuck. Should be fine to drive. If it happens again maybe you need to clean out the contacts.
Forum: 1st Generation S-series (1983-1994) Tech
03-26-2011, 06:28 PM
Replies: 5
Views: 18,446
Posted By burning_soul07

Good question, you'll have to search, but if I am...

Good question, you'll have to search, but if I am not mistaken, you will have to pull the wiring from the donor engine including ECU and all the original sensors and fuel managment components that go...
Forum: 1st Generation S-series (1983-1994) Tech
03-26-2011, 01:20 AM
Replies: 5
Views: 18,446
Posted By burning_soul07

3.4L... I would do it if I had the cash. Search...

3.4L... I would do it if I had the cash. Search that s-10 link in NEO's post. I have also followed NEO on a different forum site thats a little more active then this site.

If I am not mistaken you...
Forum: 1st Generation S-series (1983-1994) Tech
03-25-2011, 04:56 PM
Replies: 5
Views: 1,358
Posted By burning_soul07

Welcome to the forum and I hope you enjoy your...

Welcome to the forum and I hope you enjoy your 2.8L there known to be weak but can take a beating with proper maintnance.

My exhaust is pretty beat up. Leaks around the exhaust manifold. Check...
Forum: 1st Generation S-series (1983-1994) Tech
03-25-2011, 04:43 PM
Replies: 9
Views: 27,677
Posted By burning_soul07

There is a link in my signature for how to check...

There is a link in my signature for how to check the codes. Although I bet you the code your going to get is going to be because of the rough idle and not for the actual problem.
Forum: 1st Generation S-series (1983-1994) Tech
03-25-2011, 11:16 AM
Replies: 9
Views: 27,677
Posted By burning_soul07

Firing order is backwards on the 2.8L to most...

Firing order is backwards on the 2.8L to most normal chevys. Front of engine closest to radiator passanger side is #1 on the cap. Do you got this as #1?
Forum: 1st Generation S-series (1983-1994) Tech
03-25-2011, 11:12 AM
Replies: 20
Views: 36,879
Posted By burning_soul07

Check the ECM B fuse in the fuse panel by the...

Check the ECM B fuse in the fuse panel by the left drivers foot.
Forum: 1st Generation S-series (1983-1994) Tech
03-24-2011, 06:31 PM
Replies: 20
Views: 36,879
Posted By burning_soul07

Is this engine TBi or carb?

Is this engine TBi or carb?
Forum: 1st Generation S-series (1983-1994) Tech
03-24-2011, 01:09 AM
Replies: 26
Views: 10,351
Posted By burning_soul07

Check your 4x4 also, see if it works.

Check your 4x4 also, see if it works.
Forum: 1st Generation S-series (1983-1994) Tech
03-23-2011, 09:08 PM
Replies: 6
Views: 7,032
Posted By burning_soul07

What are you working on?

What are you working on?
Showing results 1 to 50 of 158
 
Page 1 of 4
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands