Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
 
Page 1 of 2
1
2
Search: Posts Made By: dlundblad
Showing results 1 to 50 of 77
Search took 0.01 seconds.
Forum: 2nd Generation S-series (1995-2005) Tech
09-12-2018, 04:59 AM
Replies: 20
Views: 1,270
Posted By dlundblad

This may require you to have the 7 prong trailer...

This may require you to have the 7 prong trailer connector as well. Just an FYI.
Forum: 2nd Generation S-series (1995-2005) Tech
09-05-2018, 04:19 AM
Replies: 2
Views: 310
Posted By dlundblad

For easy math, I'll just say the system holds 12...

For easy math, I'll just say the system holds 12 quarts.

I believe you can get 4-5 out by removing the lower radiator hose and letting air into the system by unbolting the thermostat housing.
Forum: Steering, Suspension & Drivetrain
08-30-2018, 04:49 AM
Replies: 1
Views: 461
Posted By dlundblad

I chickened out and bought an older style SKF...

I chickened out and bought an older style SKF bearing and new ABS sensor/ dust shield.
Forum: 2nd Generation S-series (1995-2005) Tech
08-30-2018, 04:47 AM
Replies: 3
Views: 396
Posted By dlundblad

I'm guessing it's a 4x4? Does 4WD work? The...

I'm guessing it's a 4x4? Does 4WD work?

The HVAC and t case is both vacuum actuated. Any leaks will make them stuck on their default position.. Defrost and feet. These have a vacuum line that runs...
Forum: Steering, Suspension & Drivetrain
08-29-2018, 04:34 AM
Replies: 7
Views: 524
Posted By dlundblad

Is that an air compressor fitting that pushes air...

Is that an air compressor fitting that pushes air in and fluid out?
Forum: 2nd Generation S-series (1995-2005) Tech
08-28-2018, 04:59 AM
Replies: 1
Views: 520
Posted By dlundblad

Could you find a non rusted frame horn at a...

Could you find a non rusted frame horn at a junkyard?

The only issue I have with the 1/8" plate is that if the bracket is already rusted at the center, the plate wont be able to do much.
Forum: 2nd Generation S-series (1995-2005) Tech
08-28-2018, 04:58 AM
Replies: 7
Views: 482
Posted By dlundblad

First, you could try some NAPA Sil Glyde on the...

First, you could try some NAPA Sil Glyde on the caliper slide pins.

I don't trust rebuilt calipers. Cardone remans calipers for Autozone, Advance, Oreilly, and NAPA. It's all junk IMO.

I've...
Forum: Website Problems and Suggestions
08-26-2018, 07:11 AM
Replies: 10
Views: 1,185
Posted By dlundblad

I'm just chiming in to say it's pretty standard...

I'm just chiming in to say it's pretty standard not discuss cat removal on car forums. I've been on car forums for over a decade and there's nothing unique or abnormal here whatsoever.
Forum: Steering, Suspension & Drivetrain
08-26-2018, 06:45 AM
Replies: 1
Views: 461
Posted By dlundblad

Hub bearing assy: 1st design vs. second

I found an older thread on the subject, but the answer was never really made clear.

Assuming I buy the newer dust shield, can the 2nd design be used? Parts stores sure treat them like they are...
Forum: 2nd Generation S-series (1995-2005) Tech
08-24-2018, 04:53 AM
Replies: 11
Views: 895
Posted By dlundblad

I think I found the answer to your problem. :)

I think I found the answer to your problem. :)
Forum: Steering, Suspension & Drivetrain
08-23-2018, 04:59 AM
Replies: 4
Views: 659
Posted By dlundblad

I would say check all the control arm bushings. ...

I would say check all the control arm bushings. Have you checked the ball joints for play?
Forum: 2nd Generation S-series (1995-2005) Tech
08-23-2018, 04:53 AM
Replies: 8
Views: 450
Posted By dlundblad

As Mike said, just make sure the diameter is...

As Mike said, just make sure the diameter is correct. Maybe measure the back of the pulley to a feature on the engine and compare that to the new part as well?

I just replaced with pulley bearing...
Forum: 2nd Generation S-series (1995-2005) Tech
08-22-2018, 09:55 AM
Replies: 24
Views: 3,932
Posted By dlundblad

Let us know how long you gravity bled them too....

Let us know how long you gravity bled them too. Thanks and good luck.
Forum: 2nd Generation S-series (1995-2005) Tech
08-19-2018, 06:09 AM
Replies: 37
Views: 2,382
Posted By dlundblad

Yes, but the engines are most likely direct...

Yes, but the engines are most likely direct injected and possibly turbo charged.. Both of which are hard on oil.

Ford Ecoboosts are about the same way.
Forum: 2nd Generation S-series (1995-2005) Tech
08-17-2018, 03:51 PM
Replies: 12
Views: 1,013
Posted By dlundblad

I thought it was grey, but I could be mistaken. I...

I thought it was grey, but I could be mistaken. I went back and looked at my photos and I think a mode selector hose was grey so it could be black. It runs about 80% the length of the dash.. Sorry,...
Forum: 2nd Generation S-series (1995-2005) Tech
08-17-2018, 04:44 AM
Replies: 12
Views: 1,013
Posted By dlundblad

The grey/ black hose is the vacuum source if I am...

The grey/ black hose is the vacuum source if I am not mistaken. Runs from the driver side firewall under the dash to the passenger side.

That said, it makes sense that if you'd disconnect...
Forum: 2nd Generation S-series (1995-2005) Tech
08-17-2018, 04:36 AM
Replies: 9
Views: 578
Posted By dlundblad

Never thought of just connecting everything...

Never thought of just connecting everything directly to the switch. Good idea.

I actually had to make an emergency run to a junkyard. I felt a little strange laying on the ground under a blazer...
Forum: 2nd Generation S-series (1995-2005) Tech
08-16-2018, 10:11 AM
Replies: 9
Views: 578
Posted By dlundblad

They may appear molded because of age.. and...

They may appear molded because of age.. and shrinkage. LOL.
Forum: 2nd Generation S-series (1995-2005) Tech
08-16-2018, 08:24 AM
Replies: 12
Views: 1,013
Posted By dlundblad

If the line is wet, the t case switch is likely...

If the line is wet, the t case switch is likely bad.

I used small picks to remove the actuators. They are clipped in.
Forum: 2nd Generation S-series (1995-2005) Tech
08-16-2018, 04:43 AM
Replies: 12
Views: 1,013
Posted By dlundblad

My truck's t case switch leaked and allowed ATF...

My truck's t case switch leaked and allowed ATF into the system.. the 4WD actuator, reservoir, and into the dash.. The actuator that moves the face vents in the center was the nastiest of the 3, but...
Forum: 2nd Generation S-series (1995-2005) Tech
08-16-2018, 04:37 AM
Replies: 2
Views: 379
Posted By dlundblad

Thanks. This will be an upcoming project for...

Thanks.

This will be an upcoming project for winter I believe.. Mine is starting to squeak pretty bad. What brand did you use?
Forum: 2nd Generation S-series (1995-2005) Tech
08-16-2018, 04:34 AM
Replies: 9
Views: 578
Posted By dlundblad

They just slide off. I just went at it with...

They just slide off.

I just went at it with wire cutters and cut the connector off the old lines so I could see what was going on. There's the actual rubber connector/ plug, but it has fittings in...
Forum: 2nd Generation S-series (1995-2005) Tech
08-14-2018, 10:10 AM
Replies: 12
Views: 1,248
Posted By dlundblad

July 2017. I bought the truck knowing the...

July 2017.

I bought the truck knowing the job needed done.

The cooling system was a mess from inadequate transitioning from Dexcool to traditional green as well as PO neglect. Finally got...
Forum: 2nd Generation S-series (1995-2005) Tech
08-14-2018, 04:54 AM
Replies: 37
Views: 2,382
Posted By dlundblad

I'm just guessing a lot has changed since you've...

I'm just guessing a lot has changed since you've been there last..

1. Many people run filters for more than one OCI. I have on my truck and my Jeep without issues, but I also use synthetic oil....
Forum: Steering, Suspension & Drivetrain
08-14-2018, 04:45 AM
Replies: 5
Views: 826
Posted By dlundblad

I compared your p/n's to those on Rock Auto's...

I compared your p/n's to those on Rock Auto's site and they look to be correct.

Sometimes you can find decent Advance Auto Parts coupons on Retailmenot.com.. Back in the day, they used to have...
Forum: 2nd Generation S-series (1995-2005) Tech
08-13-2018, 10:21 AM
Replies: 16
Views: 1,454
Posted By dlundblad

Thanks for the pictures. How'd you know the...

Thanks for the pictures.

How'd you know the wrecking yard part was any good? I'm assuming you have an SRS code reader?
Forum: 2nd Generation S-series (1995-2005) Tech
08-10-2018, 05:03 AM
Replies: 14
Views: 7,015
Posted By dlundblad

Since you're going to be replacing things, you...

Since you're going to be replacing things, you might as well get a new transfer case vacuum switch (AC Delco p/n 89059420) too.

I went through and did all the 5/32 line and 7/32 line as well as...
Forum: 2nd Generation S-series (1995-2005) Tech
08-09-2018, 04:55 AM
Replies: 14
Views: 7,015
Posted By dlundblad

I'm having a hard time believing it's engine oil....

I'm having a hard time believing it's engine oil. Just because it's dark doesn't mean it's not ATF.

Start by checking the transmission fluid and transfer case fluid levels because something is...
Forum: 2nd Generation S-series (1995-2005) Tech
08-02-2018, 12:26 PM
Replies: 24
Views: 8,030
Posted By dlundblad

I would think you could visually tell, but...

I would think you could visually tell, but measure the wheel width on the rear (which should be correct) vs. the front.
Forum: 2nd Generation S-series (1995-2005) Tech
07-15-2018, 05:07 AM
Replies: 11
Views: 2,037
Posted By dlundblad

With me at least, my transmission's ATF level is...

With me at least, my transmission's ATF level is correct and I've never once removed the fill plug and had an overfilled t case condition.
Forum: 2nd Generation S-series (1995-2005) Tech
07-14-2018, 06:05 AM
Replies: 11
Views: 2,037
Posted By dlundblad

You and I have the exact same issue. My dash is...

You and I have the exact same issue. My dash is currently out as well. I was only getting air out of the defrost and floor and so far I have been unable to find the root cause since I had replaced...
Forum: 1st Generation S-series (1983-1994) Tech
07-11-2018, 04:25 PM
Replies: 1
Views: 1,359
Posted By dlundblad

21 or 22 IIRC.

21 or 22 IIRC.
Forum: Steering, Suspension & Drivetrain
06-28-2018, 12:13 PM
Replies: 8
Views: 1,212
Posted By dlundblad

If new shocks don't cure the bounce, you may want...

If new shocks don't cure the bounce, you may want to look into the acorn shaped bump stops. They absorb the suspension travel over bumps and keep the torsion bars from over flexing.

All 4 Moog...
Forum: 2nd Generation S-series (1995-2005) Tech
06-20-2018, 03:33 PM
Replies: 6
Views: 2,178
Posted By dlundblad

I didn't think you could still buy OEM unless you...

I didn't think you could still buy OEM unless you mean the AC Delco Professional.
Forum: 2nd Generation S-series (1995-2005) Tech
06-13-2018, 03:38 PM
Replies: 3
Views: 654
Posted By dlundblad

It was me who suggested the motor mounts. It was...

It was me who suggested the motor mounts. It was only a suggestion as the vehicle isn't mine and I can't diagnose it myself so please look into it more before proceeding. I'd feel guilty if it didn't...
Forum: 2nd Generation S-series (1995-2005) Tech
06-12-2018, 04:51 AM
Replies: 3
Views: 469
Posted By dlundblad

Found it: p/n 89059420 ...

Found it: p/n 89059420

https://www.rockauto.com/en/parts/general+motors,89059420,4wd+indicator+light+switch,10775
Forum: Steering, Suspension & Drivetrain
06-11-2018, 10:33 AM
Replies: 6
Views: 677
Posted By dlundblad

Motor mount?

Motor mount?
Forum: Off Roading
06-10-2018, 06:20 PM
Replies: 37
Views: 4,208
Posted By dlundblad

Very nice.

Very nice.
Forum: 2nd Generation S-series (1995-2005) Tech
06-10-2018, 06:15 PM
Replies: 3
Views: 469
Posted By dlundblad

Which transfer case switch?

I read a while back that the improved AC Delco part had a certain color paint mark on it, but heck if I can find it. Anyone know the p/n?

Rock Auto as well as other parts stores only carry Dorman.
Forum: 2nd Generation S-series (1995-2005) Tech
06-08-2018, 04:33 AM
Replies: 13
Views: 2,872
Posted By dlundblad

Sounds like what happened to mine back in...

Sounds like what happened to mine back in November with the catalytic converter. Felt like something was dragging, no power, harsh shifts etc.

Remove an upstream 02 sensor and see if the problem...
Forum: 2nd Generation S-series (1995-2005) Tech
06-06-2018, 05:03 AM
Replies: 20
Views: 1,224
Posted By dlundblad

I'm not sure what's reasonable or not, but $228 /...

I'm not sure what's reasonable or not, but $228 / $75 an hour (just guessing) is about 3 hours so that is fair. $258 a bearing each seems a bit high, but I wonder if he went to the dealer. Did he say...
Forum: 2nd Generation S-series (1995-2005) Tech
06-03-2018, 08:41 PM
Replies: 20
Views: 1,224
Posted By dlundblad

As far as the noise, don't rule out a bad hub...

As far as the noise, don't rule out a bad hub bearing either. You can buy CV axle assemblies individually so perhaps you are thinking of something else? *If you do end up replacing the CV shafts, I...
Forum: 2nd Generation S-series (1995-2005) Tech
05-28-2018, 05:57 AM
Replies: 5
Views: 1,251
Posted By dlundblad

Sounds like you're only getting air while...

Sounds like you're only getting air while cruising, not sitting still correct?

I think it's a Chevy thing to keep fresh air inside the cab. Somewhat annoying with no AC and hot summer days.
Forum: 2nd Generation S-series (1995-2005) Tech
05-26-2018, 06:55 AM
Replies: 7
Views: 539
Posted By dlundblad

If it matters, this isn't the OE thermostat. ...

If it matters, this isn't the OE thermostat.

Rock Auto should have it for about the same price IIRC.
Forum: 2nd Generation S-series (1995-2005) Tech
05-24-2018, 05:08 AM
Replies: 7
Views: 539
Posted By dlundblad

I agree.. check to see what the sensor is telling...

I agree.. check to see what the sensor is telling the engine.

If you replace the thermostat, bite the bullet and get OE. $$$, but worth it.
Forum: Steering, Suspension & Drivetrain
05-22-2018, 07:33 AM
Replies: 9
Views: 3,193
Posted By dlundblad

Pitch: M14x2 10.9 grade. Thread length: 52.5...

Pitch: M14x2
10.9 grade.
Thread length: 52.5 mm (2.066")
Overall length: ~103.8 mm (4.086")
Major diameter near head: ~14mm and 20 mm (~.800") long.
The minor diameter at the center is 12.6 mm....
Forum: Steering, Suspension & Drivetrain
05-22-2018, 04:57 AM
Replies: 9
Views: 3,193
Posted By dlundblad

I went ahead and ordered those bolts and they...

I went ahead and ordered those bolts and they arrived while I was on vacation. I thought the heck with it and bought nuts too so I have everything ready to go. They are definitely unique and...
Forum: 2nd Generation S-series (1995-2005) Tech
05-22-2018, 04:50 AM
Replies: 3
Views: 2,757
Posted By dlundblad

People treated a ZR2 like a Ford Raptor and...

People treated a ZR2 like a Ford Raptor and wonder why the frame fails?

Oh my.
Forum: Steering, Suspension & Drivetrain
05-09-2018, 05:11 AM
Replies: 17
Views: 1,636
Posted By dlundblad

Jack of a wheel and check for play while holding...

Jack of a wheel and check for play while holding onto 12:00 and 6:00. Use a pry bar if needed.

Creaking could also be the control arm bushings.
Forum: 2nd Generation S-series (1995-2005) Tech
05-05-2018, 04:55 AM
Replies: 43
Views: 5,049
Posted By dlundblad

Synthetic vs. conventional doesn't matter as...

Synthetic vs. conventional doesn't matter as it'll say on the bottle if it has friction modifier or not.

Not sure what you guys get up North, but here the Valvoline conventional and synthetic gear...
Showing results 1 to 50 of 77
 
Page 1 of 2
1
2


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands