Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: 94_FoeDoe
Showing results 1 to 17 of 17
Search took 0.00 seconds.
Forum: Performance & Brainstorming
07-16-2013, 05:51 PM
Replies: 2
Views: 744
Posted By 94_FoeDoe

cam change

Your exhaust gas ratio will change dramatically and the engine will not run correctly. Also, the MAF on the intake sensor will have to be re-calibrated, you would have to run 93 octane gas, change...
Forum: Engine & Internal
07-16-2013, 09:09 AM
Replies: 5
Views: 2,970
Posted By 94_FoeDoe

No, the 3.4 was a replacement designed to swap...

No, the 3.4 was a replacement designed to swap out the 2.8, direct replacement motor, so it would have the "bolt holes or bosses in the block for longitudinal mounting"
Forum: Engine & Internal
07-13-2013, 01:01 PM
Replies: 5
Views: 2,970
Posted By 94_FoeDoe

Seems like for the kind of money that would cost,...

Seems like for the kind of money that would cost, $4,000, you could upgrade to a 4.3 or carb'd V8 swap,
Forum: Lowering Tech
06-01-2013, 09:02 AM
Replies: 7
Views: 2,761
Posted By 94_FoeDoe

Kind of an old thread, but instead of cutting the...

Kind of an old thread, but instead of cutting the coils use a torch to heat them up and let the weight of the vehicle compress them some more. I did this on my old '84 blazer and got about another...
Forum: 1st Generation S-series (1983-1994) Tech
05-30-2013, 06:37 PM
Replies: 6
Views: 539
Posted By 94_FoeDoe

That's what I thought it was...$5.33 @...

That's what I thought it was...$5.33 @ RockAuto.com
Forum: 1st Generation S-series (1983-1994) Tech
05-30-2013, 01:04 PM
Replies: 6
Views: 539
Posted By 94_FoeDoe

ID question

What is the plug in the air intake duct on my 1994 S10 Blazer, 4.3 "W"? mine broke and need to change it, but would rather get new one than old one out of junkyard.

Also, is there a gasket for...
Forum: 1st Generation S-series (1983-1994) Tech
05-29-2013, 08:33 AM
Replies: 28
Views: 4,198
Posted By 94_FoeDoe

I'm pretty sure mine is the fuel pump also. ...

I'm pretty sure mine is the fuel pump also. Either it is about to die, or the PO put in the pump for the "Z" engine.
Forum: 1st Generation S-series (1983-1994) Tech
05-26-2013, 12:33 PM
Replies: 28
Views: 4,198
Posted By 94_FoeDoe

Gauge works...just starts at 10 psi. Is there...

Gauge works...just starts at 10 psi. Is there another way to test the fuel pump? Other than getting a gauge that starts at a lower psi?
Forum: 1st Generation S-series (1983-1994) Tech
05-25-2013, 07:46 PM
Replies: 28
Views: 4,198
Posted By 94_FoeDoe

How else would it hook up? Just screws down on...

How else would it hook up? Just screws down on the Schrader valve right?
Forum: 1st Generation S-series (1983-1994) Tech
05-25-2013, 04:00 PM
Replies: 28
Views: 4,198
Posted By 94_FoeDoe

I'm in the same boat. Have to use starting fluid...

I'm in the same boat. Have to use starting fluid to start, but it starts and runs, hesitates when you give it gas but it will "catch up". When you kill it will not start again unless you use...
Forum: Engine & Transmission
05-18-2013, 04:04 PM
Replies: 6
Views: 4,007
Posted By 94_FoeDoe

The one in the center front was hiding. Got it...

The one in the center front was hiding. Got it off. Thanks for your help guys...Spider looks good. just a very small puddle of fuel near the #1 cylinder
Forum: Engine & Transmission
05-18-2013, 02:40 PM
Replies: 6
Views: 4,007
Posted By 94_FoeDoe

its a 94 (look at the name). I went all around...

its a 94 (look at the name). I went all around the lip of it and cannot feel another bolt...supposed to be 10, but mine only had 9 bolts
Forum: Engine & Transmission
05-18-2013, 12:57 PM
Replies: 6
Views: 4,007
Posted By 94_FoeDoe

CPI upper intake removal

Any secrets to getting this darn thing off? Pulled all the bolts out and it will not budge. Tried Rubber mallet and prybar and nothing. Any ideas?
Forum: Steering, Suspension & Drivetrain
05-14-2013, 06:26 PM
Replies: 9
Views: 1,322
Posted By 94_FoeDoe

...but it has to be a bright color like yellow,...

...but it has to be a bright color like yellow, although I heard pink was the fastest!!!
Forum: Steering, Suspension & Drivetrain
05-14-2013, 06:19 PM
Replies: 9
Views: 1,322
Posted By 94_FoeDoe

...but it has to be a bright color like yellow,...

...but it has to be a bright color like yellow, although I heard pink was the fastest!!!
Forum: Builds
05-05-2013, 08:27 AM
Replies: 56
Views: 9,618
Posted By 94_FoeDoe

Cool build. I'm not going as crazy as that, but...

Cool build. I'm not going as crazy as that, but maybe (4) 15's. I do have a couple of questions for you:
-Did you have to regulate the alternator? Is the 15+ volts your gauge is reading bad for...
Forum: New Member Area
05-03-2013, 07:21 AM
Replies: 6
Views: 391
Posted By 94_FoeDoe

LA in the house

Louisiana...not Los Angeles. Just traded a 99 Yamaha Blaster for a 94 four door LT Tahoe model. Little rough, but the body is (mostly) straight with no rust. It seems to be loaded...not much...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands