Blazer Forum - Chevy Blazer Forums - Search Results
Blazer Forum - Chevy Blazer Forums

Go Back  Blazer Forum - Chevy Blazer Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Used Blazers
Vendor Directory
Search: Posts Made By: Clay_Assassin
Showing results 1 to 37 of 37
Search took 0.01 seconds.
Forum: 2nd Generation S-series (1995-2005) Tech
12-08-2010, 12:00 PM
Replies: 8
Views: 11,766
Posted By Clay_Assassin

Isaimendez4: Pull the fuse on the ABS under the...

Isaimendez4:
Pull the fuse on the ABS under the hood to "turn off" the ABS system. The ABS light should light on the dash once the vehicle moves. If the problem is gone - It's likley in the ABS. ...
Forum: 2nd Generation S-series (1995-2005) Tech
12-06-2010, 12:54 PM
Replies: 8
Views: 11,766
Posted By Clay_Assassin

Hub was relativly new. Say 2 years old versus...

Hub was relativly new. Say 2 years old versus the other side which has 170k on it. I was hoping not to replace the hub since it was basically new, and had no play in the bearings.

We'll see how...
Forum: 2nd Generation S-series (1995-2005) Tech
12-06-2010, 09:14 AM
Replies: 8
Views: 11,766
Posted By Clay_Assassin

ABS Activation at Low Speeds

Since I'm on here often enough looking for help, I figured I would post my issue and solution:

At low speeds while braking, the ABS would activate making the characteristic grinding sound as the...
Forum: 2nd Generation S-series (1995-2005) Tech
04-12-2010, 02:01 PM
Replies: 1
Views: 732
Posted By Clay_Assassin

Intake Cooling Leak

The intake manifold has developed a slow leak at the edges.

How big a job is this? Is it better to take to a shop?

The treuck needs a lot of work, so with 150k+ on the clock I’m considering...
Forum: 2nd Generation S-series (1995-2005) Tech
08-10-2009, 07:04 AM
Replies: 3
Views: 2,719
Posted By Clay_Assassin

no special tools other than a wrench to fit on...

no special tools other than a wrench to fit on the fan nut.
I used a large adjustable and smacked it a few times with a rubber mallet to pop it loose.
Forum: Steering, Suspension & Drivetrain
12-11-2008, 11:23 AM
Replies: 3
Views: 8,325
Posted By Clay_Assassin

RE: 4x4 vacuum actuator 1998 blazer help

Your going to need a mirror most likely, like you would get at the parts store on a handle.

Hooks up to a switch on the top of the transfer case. Drivers side, on top. Stick your hand up there...
Forum: Steering, Suspension & Drivetrain
11-12-2008, 03:17 PM
Replies: 4
Views: 1,075
Posted By Clay_Assassin

RE: Front end completely shakes under speed. Here are my parts to change out. Am I missing anything?

I'm with Kyle. You may replace all that stuff to find out your steering box is shot, which is pretty typical on these blazers from what I've seen. Find out what's bad, then replace.
Forum: 2nd Generation S-series (1995-2005) Tech
10-24-2008, 08:31 AM
Replies: 1
Views: 3,540
Posted By Clay_Assassin

RE: only blows hot air

There is a damper that pushes air over the heater core. I think it's behind the glove box but not sure.
Forum: 2nd Generation S-series (1995-2005) Tech
10-07-2008, 08:12 AM
Replies: 4
Views: 2,436
Posted By Clay_Assassin

RE: Heat blows out vents on incline

Could be a loose connector that moves based on the cars position, or something else.
You say it changes when the car is on an incline, wich leads me to think a loose connector, but you dont explain...
Forum: 2nd Generation S-series (1995-2005) Tech
10-06-2008, 09:03 AM
Replies: 2
Views: 3,034
Posted By Clay_Assassin

RE: Codes on 2003 Blazer

I just had the evap leak. It proved to be the gas cap. According to the service manual, that looks like a tough nut to crack if it's not the gas cap. Dont know about the others.

The evap code...
Forum: 2nd Generation S-series (1995-2005) Tech
10-01-2008, 09:19 AM
Replies: 3
Views: 685
Posted By Clay_Assassin

RE: rebuilt pump-still no start

Knowledge is king. Nothing wrong with being cheap, but dont pay too much for your education. You will spend a lot of time and significant moneyguessing the problem.
Prove you have sufficent fuel...
Forum: 2nd Generation S-series (1995-2005) Tech
09-29-2008, 10:21 AM
Replies: 5
Views: 8,382
Posted By Clay_Assassin

Transfer Case fluid change questions

Transfer Case fill level ?

With winter coming, I’ve been getting all the maintenance items I can done on my ’98 blazer so it runs well through the snow.

I decided to change the transfer...
Forum: 2nd Generation S-series (1995-2005) Tech
09-27-2008, 10:37 AM
Replies: 7
Views: 4,153
Posted By Clay_Assassin

RE: broken passenger seat recliner

Yes, it only has one set screw, and on mine it happenes to be right at the location where the spindle hasthe notch, so it doesnt tighten down as well as it could.

The passenger side recliner...
Forum: 2nd Generation S-series (1995-2005) Tech
09-26-2008, 09:16 AM
Replies: 7
Views: 727
Posted By Clay_Assassin

RE: fuel? pressure? issues?

Kyle is correct, and changing the fuel pump can be a difficult job.
And costly. I paid ~800 bucks to have it replaced, and they had my truck for the day.

I did not want to deal with the issues...
Forum: 2nd Generation S-series (1995-2005) Tech
09-26-2008, 08:50 AM
Replies: 7
Views: 4,153
Posted By Clay_Assassin

RE: broken passenger seat recliner

I bought this, but I dont think I paid that kind of money. May have found it on another site.

http://gmseatfix.com/

http://www.wittydeals.com/product_info.php?products_id=29



It...
Forum: 2nd Generation S-series (1995-2005) Tech
09-23-2008, 07:34 AM
Replies: 6
Views: 10,468
Posted By Clay_Assassin

RE: poor gas mileage

Although I dont have milage issues with my blazer, I had a '98 corvette that got lousy milage for about 3 years while I tried to figure out the problem. I did everything too it you could think of,...
Forum: 2nd Generation S-series (1995-2005) Tech
09-22-2008, 03:01 PM
Replies: 3
Views: 972
Posted By Clay_Assassin

RE: Heater A/C Control help please!

I didn't mean to imply no one knew anything period, the statement was in regards to this specific repair. Not everyone can know every repair issue.

Also, I have the GM service manual for the...
Forum: 2nd Generation S-series (1995-2005) Tech
09-22-2008, 10:06 AM
Replies: 1
Views: 2,843
Posted By Clay_Assassin

RE: driverside door lock jammed????

I had door lock problems on mine once. While trying to solve the issue, it locked up so tight I couln't unlock it, so Maybe this will help:

The interior door handle is spring loaded, so when you...
Forum: 2nd Generation S-series (1995-2005) Tech
09-22-2008, 09:56 AM
Replies: 15
Views: 3,488
Posted By Clay_Assassin

RE: Vaccum Supply to vent control

I just solved this issue.

There is a bank of solenoids behind the ashtray. For me, the solenoids failed.

If your climate control has an “Auto” setting, you also have these solenoids.
...
Forum: 2nd Generation S-series (1995-2005) Tech
09-22-2008, 09:49 AM
Replies: 3
Views: 11,690
Posted By Clay_Assassin

RE: only blow air through dash vents when set to floor or defrost

I just stumbled across your post looking for another one, and I had just solved this issue on my vehicle.

You have a failure at the actuator which closes off the panel vents, and directs air to...
Forum: 2nd Generation S-series (1995-2005) Tech
09-22-2008, 09:05 AM
Replies: 3
Views: 972
Posted By Clay_Assassin

RE: Heater A/C Control help please!

Since nobody seemed to know anything, I took a stab at the solution myself:

First I purchased both parts new. Plugged in the new head unit, it didn’t change my A/C issue.
Plugged in the new...
Forum: 2nd Generation S-series (1995-2005) Tech
09-19-2008, 02:04 PM
Replies: 4
Views: 1,251
Posted By Clay_Assassin

RE: Replacing ball joints help

The part you have looks similar to my '98. I installed the moog. However, my father-in-law (GM mechanic) said he was "suprised my ball joints were bolted in, as usually they are rivited, and you have...
Forum: 2nd Generation S-series (1995-2005) Tech
09-18-2008, 01:43 PM
Replies: 60
Views: 3,853
Posted By Clay_Assassin

RE: Cold temp. starting issue

I would go out and start it before its light out, with somebody helping. See if you can see sparks. I've had wires go bad in just a few months. Heat from surrounding engine parts can thin the...
Forum: 2nd Generation S-series (1995-2005) Tech
09-17-2008, 09:13 AM
Replies: 3
Views: 972
Posted By Clay_Assassin

Heater A/C Control help please!

I’ll tell you exactly what I know, so maybe somebody who has worked through this can help quickly or at least point me in the right direction.

The Heat-A/C always comes out the panel. It wont...
Forum: Steering, Suspension & Drivetrain
05-13-2008, 02:25 PM
Replies: 4
Views: 10,183
Posted By Clay_Assassin

RE: Replacing front axle CV boot (inner)

I have the same problem. Both inner boots are shot, spraying grease everywhere. What I have learned so far:
A nice boot will cost $17 bucks, plus the effort to replace it. Replacement is a big job....
Forum: 2nd Generation S-series (1995-2005) Tech
03-18-2008, 09:36 AM
Replies: 1
Views: 818
Posted By Clay_Assassin

RE: HVAC Air Directional Issues - Please Help

Somebody out there has to know something about this????
Forum: 2nd Generation S-series (1995-2005) Tech
03-10-2008, 09:43 AM
Replies: 1
Views: 818
Posted By Clay_Assassin

HVAC Air Directional Issues - Please Help

Hi,
I have a '98 blazer. The heat ALWAYS comes out the vents on the dash. It will come out on the floor, or the defrost as well, but the vents are always on.
I located the two vacuum valves under...
Forum: 2nd Generation S-series (1995-2005) Tech
02-19-2008, 09:02 AM
Replies: 4
Views: 744
Posted By Clay_Assassin

RE: 4wd not working

I doubt it. The 4wd is a two part system. Need more information to try to help you. What do you mean the switch doesnt work?
Forum: 2nd Generation S-series (1995-2005) Tech
02-19-2008, 08:52 AM
Replies: 15
Views: 3,488
Posted By Clay_Assassin

RE: Vaccum Supply to vent control

I've got a similar problem with mine. Stuck in vent. Wont blow on the floor or the defrost.
Hopeing to look at it this weekend.
Forum: Steering, Suspension & Drivetrain
01-02-2008, 10:25 AM
Replies: 4
Views: 2,927
Posted By Clay_Assassin

RE: Creaking noise coming from front end

For me, that weird noise was the lower ball joints.
Forum: Steering, Suspension & Drivetrain
01-02-2008, 10:24 AM
Replies: 3
Views: 2,548
Posted By Clay_Assassin

RE: Feels like it is waving in the wind(its not windy)!!!

Mine was pretty bad. Needed new lower ball joints and a new steering gear.

Did the ball joints last week.It drives better already. Not a bad job, just a headache. Will do the steering gear in...
Forum: Steering, Suspension & Drivetrain
12-08-2007, 07:54 PM
Replies: 1
Views: 1,331
Posted By Clay_Assassin

RE: 4x4 question with whining noise

I had a noise like that, turned out to be a bad bearing. Check the fron bearings on the vehicle.

Chack the car up, grab wheel at 9:00 and 6:00. Shake wheel bck and forth towards you noting...
Forum: Steering, Suspension & Drivetrain
12-08-2007, 07:47 PM
Replies: 7
Views: 2,162
Posted By Clay_Assassin

RE: Trans issues after fluid change. PLease help

Year of vehicle? Milage? Last trans fluid and filter change?

Rumor is, that if a vehicle is not well maintained, and you change the transmission fluid, you run the risk of advancing the failure...
Forum: Steering, Suspension & Drivetrain
12-08-2007, 07:38 PM
Replies: 5
Views: 1,006
Posted By Clay_Assassin

RE: 4WD not working - Little help please

Thank you sir. I do not believe there is a vacuum leak, but I will double check. The actuator really yanks on the cable hard. The cable does move both by hand, and under vacuum. I can see it pull in...
Forum: Steering, Suspension & Drivetrain
12-08-2007, 02:46 PM
Replies: 5
Views: 1,006
Posted By Clay_Assassin

RE: 4WD not working - Little help please

I have replaced the switch on the transfer case.
I now have vacuum at the actuator under the battery.
The vacuum actuator appears to be working well/properly.

4wd still does not engage....
Forum: Steering, Suspension & Drivetrain
12-06-2007, 01:28 PM
Replies: 5
Views: 1,006
Posted By Clay_Assassin

RE: 4WD not working - Little help please

Actually Hanr3, I started with your message. Thank you very much for that post. If it wasn't for you, I may have given up. The service manual seems to have missed providing the excellent information...
Forum: Steering, Suspension & Drivetrain
12-04-2007, 08:00 PM
Replies: 5
Views: 1,006
Posted By Clay_Assassin

4WD not working - Little help please

Looking for a little help with 4WD. Transfer case switches, front hubs do not engauge. Driveshaft engages.
Checked vacuum actuator. It's kinda sticky, but appears to hold vacuum. It may be working....
Showing results 1 to 37 of 37


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

© 2021 MH Sub I, LLC dba Internet Brands