Blazer Forum - Chevy Blazer Forums
top view
top view
0 2013/07/16 20:24:46
switch mount in car working
switch mount in car working
0 2013/07/16 20:24:46
switch mount i made to cover cd holder
switch mount i made to cover cd holder
0 2013/07/16 20:24:46
under edge of the wheel well mounted half of the flare
under edge of the wheel well mounted half of the flare
0 2013/07/16 00:02:51
view of the rear passenger door open, with me holding the flare mocked into place, see the inside edge of the flare and door
view of the rear passenger door open, with me holding the flare mocked into place, see the inside edge of the flare and door
0 2013/07/16 00:02:51
view of the rear passenger door open, with me holding the flare mocked into place
view of the rear passenger door open, with me holding the flare mocked into place
0 2013/07/16 00:02:51
joint of the door mounted part of the flare and the well mounted part of the flare
joint of the door mounted part of the flare and the well mounted part of the flare
0 2013/07/16 00:00:52
mount for the door, view of the lower screw hole
mount for the door, view of the lower screw hole
0 2013/07/16 00:00:52
mount for the door, view of the top screw hole
mount for the door, view of the top screw hole
0 2013/07/16 00:00:52
close up view of the joint where to the two pieces come together
close up view of the joint where to the two pieces come together
0 2013/07/15 23:57:33
this is a view of the passenger side rear. with the part of the flare that mounts to the wheel well already installed
this is a view of the passenger side rear. with the part of the flare that mounts to the wheel well already installed
0 2013/07/15 23:57:33
piece on the top (was my right) is the actual flare, it automotive double sided adhesives to the piece on my left (the bottom) which is the mount, the mount uses the 3m auto tape and two small screws to hold itself on.
piece on the top (was my right) is the actual flare, it automotive double sided adhesives to the piece on my left (the bottom) which is the mount, the mount uses the 3m auto tape and two small screws to hold itself on.
0 2013/07/15 23:57:33
my new fender flares (i havent put the door piece on the rear but these are REAL UNMODIFIED 4 door fender flares)
my new fender flares (i havent put the door piece on the rear but these are REAL UNMODIFIED 4 door fender flares)
0 2013/07/15 21:42:40
my new fender flares (i havent put the door piece on the rear but these are REAL UNMODIFIED 4 door fender flares)
my new fender flares (i havent put the door piece on the rear but these are REAL UNMODIFIED 4 door fender flares)
0 2013/07/15 21:39:01
my new fender flares (i havent put the door piece on the rear but these are REAL UNMODIFIED 4 door fender flares)
my new fender flares (i havent put the door piece on the rear but these are REAL UNMODIFIED 4 door fender flares)
0 2013/07/15 21:39:01
my 99% completed push bar setup (nothings ever done lol)
my 99% completed push bar setup (nothings ever done lol)
0 2013/07/15 21:39:01
repainted most of the frame
repainted most of the frame
0 2011/11/28 09:01:46
repainted the tow hooks
repainted the tow hooks
0 2011/11/28 09:01:46
double din dash bezel :)
double din dash bezel :)
0 2011/11/28 09:01:46
fixed the center console
fixed the center console
0 2011/11/28 08:51:14
aww, new stuff :)
aww, new stuff :)
0 2011/11/28 08:51:14
after lots of WD-40 lol
after lots of WD-40 lol
0 2011/11/28 08:41:40
new parts :D
new parts :D
0 2011/11/28 08:41:40
needing some new parts
needing some new parts
0 2011/11/28 08:41:40
quick back shot, with my dad in it lol
quick back shot, with my dad in it lol
0 2011/11/27 20:19:27
quick front shot
quick front shot
0 2011/11/27 20:19:27