what have you gotten done on your blazer today?
Super Member
Joined: Jun 2010
Posts: 1,594
From: Char-town, NC
.
could you get me the part # for the bulbs? I realized mine was out too a few weeks ago.
Yours is 4wd right? I bet 10 cents its going to be the oil line adapter on the block (where the filter woulda gone if it was a 2wd.) they like to leak and make it look like a crank seal. Pressure wash it all off at the car wash and drive it home,then lay down,get comfortable and watch for runs. lol
Yours is 4wd right? I bet 10 cents its going to be the oil line adapter on the block (where the filter woulda gone if it was a 2wd.) they like to leak and make it look like a crank seal. Pressure wash it all off at the car wash and drive it home,then lay down,get comfortable and watch for runs. lol
BF Veteran
Joined: Sep 2008
Posts: 2,522
From: Winnipeg, Manitoba
Lifted the front, removed the tires & tightened up what I was supposed to do a month after the RC install in April lol. Rides much better on the way home.
Then I took the PS valve cover off AGAIN & went at the rockers. I knew the front PS exhaust was making noise after setting it numerous times so I figured it was either a bent valve, buggered up guide or bad lifter because if i took the rocker off - noise went away.
I also found another rocker that could have used a little "tweaking" so I did that one too. Clickety wasn't there on the ride home!
But halfway I started to hear what sounds like a bearing on an upfront accessory going.
Off beat, non synchronous squeaking up & down & with engine revs. Grrrrrrrrrr. They way the sound articulates it seems like the tensioner.
Not a bad day I suppose... also filled the pig up to the tune of $70 on 87 octane.
<edit> Oh yeah I cleaned the air filter. On the way home it didn't hessitate, back fire up the throttle body like it did when cold before. Got a MAF & 02 code though, but that was probably because I was running it without the SC plumbed to the intake. It wasn't getting the air it's been programmed to & that's probably what set the codes off. I used the ELM & cleared them, ran the ELM all the way home & they didn't pop up again.
We'll see what tomorrow holds though lol.
Then I took the PS valve cover off AGAIN & went at the rockers. I knew the front PS exhaust was making noise after setting it numerous times so I figured it was either a bent valve, buggered up guide or bad lifter because if i took the rocker off - noise went away.
I also found another rocker that could have used a little "tweaking" so I did that one too. Clickety wasn't there on the ride home!
But halfway I started to hear what sounds like a bearing on an upfront accessory going.
Off beat, non synchronous squeaking up & down & with engine revs. Grrrrrrrrrr. They way the sound articulates it seems like the tensioner.
Not a bad day I suppose... also filled the pig up to the tune of $70 on 87 octane.
<edit> Oh yeah I cleaned the air filter. On the way home it didn't hessitate, back fire up the throttle body like it did when cold before. Got a MAF & 02 code though, but that was probably because I was running it without the SC plumbed to the intake. It wasn't getting the air it's been programmed to & that's probably what set the codes off. I used the ELM & cleared them, ran the ELM all the way home & they didn't pop up again.
We'll see what tomorrow holds though lol.
Last edited by Rottidog; Oct 6, 2012 at 08:22 PM.
New Member
Joined: Jun 2012
Posts: 57
From: Crowley, LA
A weekish ago i trimmed that baffle shiz off my throttle blade. A lil better pep! =} friday, i changed my front brakes and driver side hub and rotor. Damn rotor was siezed to the hub. Ruined it by having to beat it off with a lil sledge hammber thing. Greased all that jazz for the brakes. Brakes havent felt that good since i got it!! =} two weeks from now ill be doing the passenger side. Just for precautionary reasons. =}
Senior Member
Joined: Oct 2010
Posts: 647
From: West-Central MA
Only reason I run Amsoil in our '00 Jimmy engine in the Blazer is because I'm a dealer, so after selling oil to others I end up paying less for this than I would for conventional. It's a no-brainer in this case. Just so happens that engine is sitting in the barn right now on a stand - had to yank it for the exact problem your having. Every gasket, seal & freeze plug is being replaced while it's out.
My pan was pissing out the front driver's side corner. Even though I get synthetics cheap, I still don't want to waste them.
Super Member
Joined: Apr 2012
Posts: 1,279
From: Port huron,Mi
Slow progress
After taking a hiatus from doing anything Im actualy getting somethings accomplished.Mainly wire harness connections and things like that.Also hooked the altenator.The engine is slowly coming together but the trans and transfer case still has to be reinstalled.I hopefully I can get that stuff in a couple of weeks.
Starting Member
Joined: Jul 2010
Posts: 145
From: New York
Thanks for reminding me... I've had a short bungee cord and scrap of wood holding in the button on the passenger's side for the past year or so. Of course, it broke when out with GF and she tried to use the mirror...
Beginning Member
Joined: Mar 2012
Posts: 17
From: Upland, CA.
washed waxed and clayed
i hope not in that order. should be wash clay polish wax i own all american detailing and will give any blazer owner the proper method and technique they need to keep them clean and happy.
Beginning Member
Joined: Apr 2011
Posts: 26
From: Upstate New York
Went out for a drive on the father in laws lot. Took the jimmy, I was happy that the 4wd ran like a dream. Had to keep it in 4lo due to the hill and the ruts in his lot. Ran though it like it was nothing. It was happy to get its exercise find quarks and work on fixing the issues later. Still need to do the motor mounts that will be next month though. Being that I don't drive though a lot of lots like I did today I think I'll stick with OEM mounts.