what have you gotten done on your blazer today?
#7432
I like it!!!
#7435
Fresh coat of 4 inches of snow... Took her to go pay the insurance bill and to pick up a set of brake shoes for the k1500... Facking napa sold me the wrong shoes. SO off to town again tomorrow.
Also my dads s10 pickup keeps overheating... She gets to 250. When I open the hood the engine is cold. I can place my hand on the motor with out burning my self.
Well after then I notice I had no heat and then all of a sudden the temp dropped... and every thing went back to normal meaning the thermostat is stuck from my point of view. Time to go swap thermostats in the morning too since its under warranty.
Posting more pictures and 2 videos my mom took on the way home in my build thread.
Here is a teaser
Also my dads s10 pickup keeps overheating... She gets to 250. When I open the hood the engine is cold. I can place my hand on the motor with out burning my self.
Well after then I notice I had no heat and then all of a sudden the temp dropped... and every thing went back to normal meaning the thermostat is stuck from my point of view. Time to go swap thermostats in the morning too since its under warranty.
Posting more pictures and 2 videos my mom took on the way home in my build thread.
Here is a teaser
#7436
Today I did the distributor rotor and cap, and wires and ac delco platnium plugs, fuel filter, and yesterday I did the brake fluid change and cleaned and greased the brakes, cleaned out the maf sensor and throtlebody, and changed the oil and went the 5w20 route was on sale for 18 bucks, and a 5 buck motomaster filter. Had the diffs, trany, trans case fluids changed at the shop and allignment and a new friction modifier for the rear locker. And i cleaned out the k&n air filter. Tomorrow i plan on lubein the chassis, flushin the heater core and coolant, checking the pcv, eec, and o2's, insulating the doors and undercoating, and adjusting the head lights since a raised the t bars and got shakles and new 31" tires. And after that I gotta bondo up the triming i did to make that fit. and i gotta get the shop to spray through the fuel injectors and tune the timings, then i should be all set, 129,9XX kms, thats 80,000 miles on the blazer now got it with 50,000 on it 3 years ago So far only thing to die was the starter, ball joints, and a caliper.
Last edited by Dustyrandall; 01-16-2013 at 09:43 PM.
#7437
Today I did the distributor rotor and cap, and wires and ac delco platnium plugs, fuel filter, and yesterday I did the brake fluid change and cleaned and greased the brakes, cleaned out the maf sensor and throtlebody, and changed the oil and went the 5w20 route was on sale for 18 bucks, and a 5 buck motomaster filter. Had the diffs, trany, trans case fluids changed at the shop and allignment and a new friction modifier for the rear locker. And i cleaned out the k&n air filter. Tomorrow i plan on lubein the chassis, flushin the heater core and coolant, checking the pcv, eec, and o2's, insulating the doors and undercoating, and adjusting the head lights since a raised the t bars and got shakles and new 31" tires. And after that I gotta bondo up the triming i did to make that fit. and i gotta get the shop to spray through the fuel injectors and tune the timings, then i should be all set, 129,9XX kms, thats 80,000 miles on the blazer now got it with 50,000 on it 3 years ago So far only thing to die was the starter, ball joints, and a caliper.
#7438
New paint job
Over the weekend I painted the body line and frame so I didnt have to stare at rust cancer anymore. I used SEM Undercoating in rattle can form. Had to do a little bondo work in two spots. Next I have to do the grill. Pictures are in my album.