Blazer Forum - Chevy Blazer Forums
Ready to hit the streets, jamming on some tunes, with friends or family!
Ready to hit the streets, jamming on some tunes, with friends or family!
0 2013/09/05 22:31:00
All waxed up and looking sharp.
All waxed up and looking sharp.
0 2013/09/05 22:31:00
Out tanning in the sun....LOL!
Out tanning in the sun....LOL!
0 2013/09/05 22:31:00
Got it made in the shade (a little corny I know) !
Got it made in the shade (a little corny I know) !
0 2013/09/05 22:41:11
Shine-Oh-Mite !!
Shine-Oh-Mite !!
0 2013/09/05 22:41:11
Looking Good !
Looking Good !
0 2013/09/05 22:43:30
You'll see the back end of this pulling you out of the ditch if you don't drive with common sense. Especially with Minnesota winters. You still have four wheels like the rest of the people on the road, Please Drive Carefully !
You'll see the back end of this pulling you out of the ditch if you don't drive with common sense. Especially with Minnesota winters. You still have four wheels like the rest of the people on the road, Please Drive Carefully !
0 2013/09/05 22:51:02
Yes, it has the Vortec V-6 (4.3 L), four speed transmission,and 4 WD. This Blazer has 241,550 miles on her and still going strong. Switched over to Valvoline Max-Life 5W-30 Motor oil @200,000 Miles.
Yes, it has the Vortec V-6 (4.3 L), four speed transmission,and 4 WD. This Blazer has 241,550 miles on her and still going strong. Switched over to Valvoline Max-Life 5W-30 Motor oil @200,000 Miles.
0 2013/09/05 22:51:02
I had gouges in the rear bumper trim (because my sister owned the vehicle before I did and seemed to back into alot of things) and I used Spot Putty to fill in the low areas. I then sanded it with 1200 Grit (wet or dry) sand paper. Taped the area off and primered it, sanded it until it was uniformally smooth and painted it with Spray Max 1K Black Trim Paint (11.3 oz) at Napa Auto parts for $14.00.
I had gouges in the rear bumper trim (because my sister owned the vehicle before I did and seemed to back into alot of things) and I used Spot Putty to fill in the low areas. I then sanded it with 1200 Grit (wet or dry) sand paper. Taped the area off and primered it, sanded it until it was uniformally smooth and painted it with Spray Max 1K Black Trim Paint (11.3 oz) at Napa Auto parts for $14.00.
0 2013/09/05 23:02:09
Worked on replacing the silver part on this two piece body moulding by using silver lower door panel guard (outer) and wrapped it around the silver part of the trim and reattached it with 3-M double faced tape. On the rest of the body trim, I had to cut the silver part off (you have to pull the entire trim piece off,remove old adhesive tape from body and the trim) and wrapped it the same way there is about an 1/8 of an inch that is on the back of the trim. I wrapped it that way to keep out water, dirt and salt. It is a little tricky, but its well worth the results. Only time will tell how it holds up !
Worked on replacing the silver part on this two piece body moulding by using silver lower door panel guard (outer) and wrapped it around the silver part of the trim and reattached it with 3-M double faced tape. On the rest of the body trim, I had to cut the silver part off (you have to pull the entire trim piece off,remove old adhesive tape from body and the trim) and wrapped it the same way there is about an 1/8 of an inch that is on the back of the trim. I wrapped it that way to keep out water, dirt and salt. It is a little tricky, but its well worth the results. Only time will tell how it holds up !
0 2013/09/05 23:02:09
Working on cosmetics and of course a few dings !
Working on cosmetics and of course a few dings !
0 2013/09/05 23:02:09