2nd Generation S-series (1995-2005) Tech Discuss 2nd generation S-series (1995-2005) general tech topics here.

Hot brake rotors

Old Aug 18, 2017 | 02:17 PM
  #1  
Willyclay's Avatar
Thread Starter
|
Beginning Member
Joined: Aug 2017
Posts: 11
Willyclay is on a distinguished road
Default Hot brake rotors

New member and old geezer with 98 Blazer, four-door, 2WD, LS model with 124K+ miles. Independent shop replaced R.R. caliper that was sticking plus new pads in both rears. Told me they test drove it after repairs and realized the parking brakes were on. When I picked it up, the parking brakes seemed ok. About 30 days later, the R.R. caliper was sticking again and was replaced plus a new hose. After a few thousand miles, I realized the parking brakes were not holding well and decided to replace them myself. I did and found the adjusters were both at "zero" but the cable had been tightened significantly. Had to back off the cable a bunch to get new parking brake linings not to drag. Put it all back together and drove it less than 100 miles and found the L.R caliper was sticking. Replaced that and the hose myself and everything seemed right; minimal drag, even braking, good pedal, no leaks. no noise. My concern is the L.R. rotor temperature is consistently 50-60 degrees hotter than the R.R. rotor according to my Harbor Freight Laser thermometer! Do I still have a problem with brakes or is that just the way these old Blazers are?
 
Old Aug 18, 2017 | 04:15 PM
  #2  
newguy's Avatar
BF Veteran
Joined: Feb 2012
Posts: 4,205
From: Easthampton, ma.
newguy will become famous soon enoughnewguy will become famous soon enough
Default

Could be old rubber brake lines. They will imploded and not release
 
Old Aug 18, 2017 | 04:44 PM
  #3  
GeorgeLG's Avatar
BF Veteran
Joined: Jan 2007
Posts: 4,628
From: Florida
GeorgeLG will become famous soon enoughGeorgeLG will become famous soon enough
Default

Sometimes a caliper rebuild can malfunction. Either the piston won't release or the pins and slider gets hung up.

+1 on the rubber hose.

George
 
Old Aug 18, 2017 | 05:13 PM
  #4  
Willyclay's Avatar
Thread Starter
|
Beginning Member
Joined: Aug 2017
Posts: 11
Willyclay is on a distinguished road
Default

L.R. has new hose but a reman caliper. Prefer new mechanical parts but went with the reman because it was the only one at my local parts store.
 
Old Aug 18, 2017 | 07:19 PM
  #5  
GeorgeLG's Avatar
BF Veteran
Joined: Jan 2007
Posts: 4,628
From: Florida
GeorgeLG will become famous soon enoughGeorgeLG will become famous soon enough
Default

I use reman calipers also but I am careful with the brand and check operation at the install to be certain that they release correctly and the slide pins are slick etc.

George
 
Old Oct 11, 2017 | 07:58 PM
  #6  
Willyclay's Avatar
Thread Starter
|
Beginning Member
Joined: Aug 2017
Posts: 11
Willyclay is on a distinguished road
Default

UPDATE: After 20 miles of around-town driving today, RR rotor was 135F but LR rotor was 235F. Considering a complete brake fluid flush. Comments?
 
Old Oct 11, 2017 | 08:19 PM
  #7  
LannyL81's Avatar
Super Member
Joined: Oct 2008
Posts: 1,786
From: Tucson, Arizona
LannyL81 will become famous soon enough
Default

What condition are the rear rotors in? Fluid flush is always a good thing to do if not been done for awhile.
Check those sliders and be sure to use the proper grease.
 
Old Oct 11, 2017 | 09:24 PM
  #8  
Willyclay's Avatar
Thread Starter
|
Beginning Member
Joined: Aug 2017
Posts: 11
Willyclay is on a distinguished road
Default

Thanks for the reply. Rotors are excellent by my old geezer eyes. Slider seemed good before installing the reman caliper on the LR but will check it again and report back.
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
10-78 edac
2nd Generation S-series (1995-2005) Tech
2
Apr 24, 2012 09:24 AM
Mandrwj
Engine & Transmission
5
Apr 10, 2011 07:32 PM
vze4yrte
2nd Generation S-series (1995-2005) Tech
9
Aug 30, 2010 09:08 PM
ravenhurst
2nd Generation S-series (1995-2005) Tech
15
Apr 26, 2009 07:53 AM
leritz
General Tech Help
2
Sep 6, 2006 03:04 PM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 08:30 PM.