Engine & Transmission Post your Engine and Transmission related problems here.

01 Blazer stalling

Old Jun 21, 2011 | 12:18 AM
  #1  
MakaveIi's Avatar
Thread Starter
|
New Member
Joined: Aug 2009
Posts: 75
From: Hammond, IN
MakaveIi is on a distinguished road
Default 01 Blazer stalling

My truck stalls when I let off the gas. Sometimes it starts up and runs normally, but usually it will die immediately if I dont rev the engine. It will die at stop signs/lights and turns if I don't shift to neutral and keep it revving. Replaced plugs and wires, cap and rotor, and ignition coil with no change in performance. Slight gas smell on some start ups. Not sure what do next...
 
Old Jun 21, 2011 | 09:19 AM
  #2  
chris015's Avatar
BF Veteran
Joined: Apr 2009
Posts: 3,748
From: South Carolina
chris015 is a jewel in the roughchris015 is a jewel in the roughchris015 is a jewel in the rough
Default

From the gas smells etc. Id check fuel pressure. It needs to be at key on 55-60 psi. If the pressure falls while key on the fuel regulator is leaking.
 
Old Jun 21, 2011 | 12:00 PM
  #3  
swartlkk's Avatar
Administrator
Joined: May 2005
Posts: 41,332
From: Waterloo, NY
swartlkk has a reputation beyond reputeswartlkk has a reputation beyond reputeswartlkk has a reputation beyond reputeswartlkk has a reputation beyond reputeswartlkk has a reputation beyond reputeswartlkk has a reputation beyond reputeswartlkk has a reputation beyond reputeswartlkk has a reputation beyond reputeswartlkk has a reputation beyond reputeswartlkk has a reputation beyond reputeswartlkk has a reputation beyond repute
Default

Checking the fuel pressure isn't a bad idea. You could also run through some of the other DIY maintenance items such as cleaning the:
  • throttle body (including the IAC bore)
  • the MAF sensor
  • and the EGR valve
Check out the Tech Article (DIY) Index link in my signature below for links to explanations of these specific tasks.
 
Old Jul 12, 2011 | 10:46 PM
  #4  
MakaveIi's Avatar
Thread Starter
|
New Member
Joined: Aug 2009
Posts: 75
From: Hammond, IN
MakaveIi is on a distinguished road
Default

I ended up burning through my alternator wire, so I finished my Big 3 and put the 1/0 ga wire in and it hasn't died since, but it still had the rough idle until a couple days ago. My intake gasket blew, my truck sounded like a tea kettle, but after that it ran a lot smoother. I replaced the gasket today, along with the thermostat, and went ahead and put a new spider injector in. I'll finish putting it all together tomorrow morning, and we'll see how it runs.


UPDATE: Finished everything today, runs great.
 

Last edited by MakaveIi; Jul 14, 2011 at 12:21 AM.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
skoot61
2nd Generation S-series (1995-2005) Tech
12
Jul 21, 2008 07:29 PM
pkallis
2nd Generation S-series (1995-2005) Tech
1
Jun 23, 2008 11:07 AM
ralph10
1st Generation S-series (1983-1994) Tech
1
Mar 23, 2007 01:21 PM
dragonsdeath
General Tech Help
3
Oct 7, 2006 01:08 AM
Urenemy
General Tech Help
6
Jul 7, 2006 02:40 PM


Thread Tools
Search this Thread

All times are GMT -5. The time now is 04:35 AM.