what have you gotten done on your blazer today?
#4042
09-23-2011, 08:29 AM
Went out to my blazer today and installed my stinger volt meter along with my pioneer head unit. Everything went well except now my rear wiper doesn't work. I will get to trouble shooting it later. Hopefully the rain will stop.
#4045
09-23-2011, 03:52 PM
I got my cluster and installed it its great to have a cluster again
But my horn fuse is still melting ....
I might have a short somewhere i tryed a weaker fuse and it still wont blow but it gets hot
it sparks a lot while inserting it
if you guys got any idea please dont hesitate to respond in my other thread
https://blazerforum.com/forum/lighti...e2/#post462224
Edit: fixed it turned out to be the dumb alarm my uncle got installed when he owned the truck thanks guys =)
But my horn fuse is still melting ....
I might have a short somewhere i tryed a weaker fuse and it still wont blow but it gets hot
it sparks a lot while inserting it
if you guys got any idea please dont hesitate to respond in my other thread
https://blazerforum.com/forum/lighti...e2/#post462224
Edit: fixed it turned out to be the dumb alarm my uncle got installed when he owned the truck thanks guys =)
Last edited by xgiovannix12; 09-23-2011 at 06:49 PM.
#4046
09-23-2011, 07:01 PM
Well $250 later and I have a new battery installed and my hids (55w 8000k) and h4 sealed-beam conversion lamps are ordered. That was an expensive hour.
#4047
09-23-2011, 07:02 PM
Well $250 later and I have a new battery installed and my hids (55w 8000k) and h4 sealed-beam conversion lamps are ordered. That was an expensive hour.
haha i agree
#4049
09-25-2011, 07:42 AM
Yesterday she got new rear breaks. And cleaned up front breaks too. Then that night at autozone I found a d- ring shackle for 15bucks.
#4050
09-25-2011, 10:32 AM
Hi everyone.
New member here.
"WOW" I'm very happy to have found this forum for these vehicles. A "virtual" mountain of information at my fingertips.
Today I cleaned up all parts to put back together my right front hub assembly on my 96 LS. Had to replace steering knuckle too. Was fortunate to get a complete hub assembly from the wreckers for 50 bucks.
Now i do have a question though if anyone can answer it? I hope I can ask here? If not then straighten me out from the get go.
There is a seal that needed and I am replacing where the CV joint goes through the steering knuckle (on the steering knuckle) which is coming tomorrow. I also noted there is a seal in the hub assembly for the bearing(s?) Is it possible to remove this seal, grease the bearings and install a new seal or am I better off leaving well enough alone?
Thank you peoples.
New member here.
"WOW" I'm very happy to have found this forum for these vehicles. A "virtual" mountain of information at my fingertips.
Today I cleaned up all parts to put back together my right front hub assembly on my 96 LS. Had to replace steering knuckle too. Was fortunate to get a complete hub assembly from the wreckers for 50 bucks.
Now i do have a question though if anyone can answer it? I hope I can ask here? If not then straighten me out from the get go.
There is a seal that needed and I am replacing where the CV joint goes through the steering knuckle (on the steering knuckle) which is coming tomorrow. I also noted there is a seal in the hub assembly for the bearing(s?) Is it possible to remove this seal, grease the bearings and install a new seal or am I better off leaving well enough alone?
Thank you peoples.
Last edited by Spacemanspiff; 09-25-2011 at 10:36 AM.