Blazer Forum - Chevy Blazer Forums
0 2020/02/08 08:23:28
0 2020/02/07 07:45:56
0 2020/02/07 07:44:41
0 2020/02/07 07:43:50
0 2020/02/07 07:43:17
now its hone tine... ...will take couple hours.
now its hone tine... ...will take couple hours.
0 2020/01/24 02:03:20
first strokes on the worst cylinder 0,08 mm inequality ()
first strokes on the worst cylinder 0,08 mm inequality ()
0 2020/01/24 02:01:27
and the torque plate
and the torque plate
0 2020/01/24 01:26:16
used MLS
used MLS
0 2020/01/24 01:23:09
0 2020/01/24 01:15:19
setting up
setting up
0 2020/01/24 00:52:32
0 2020/01/24 00:51:46
0 2020/01/21 08:58:54
cam bearings out, all cam bearing bores chamfered, cylinder bases chamfered, ready to be honed. we have decided against boring. with the new forged pistons which are 0,002 inches over we save pn machining and retain maximum wall thickness for nitrous or such experiments. ;)
cam bearings out, all cam bearing bores chamfered, cylinder bases chamfered, ready to be honed. we have decided against boring. with the new forged pistons which are 0,002 inches over we save pn machining and retain maximum wall thickness for nitrous or such experiments. ;)
0 2020/01/17 11:45:58
chamfering the lifter bores from.below - pure cosmetic.
chamfering the lifter bores from.below - pure cosmetic.
0 2020/01/17 11:40:27
measuring the clearance in the lifter bores
measuring the clearance in the lifter bores
0 2020/01/17 11:40:16
after the first cut. the right side was the high side. now we cut from here.
after the first cut. the right side was the high side. now we cut from here.
0 2020/01/17 11:36:28
first cut to get the deck square 0,03mm (0,001 inch)
first cut to get the deck square 0,03mm (0,001 inch)
0 2020/01/17 11:36:17
square the block on the mill.
square the block on the mill.
0 2020/01/17 11:34:33
rocker arm witness mark on valve stem. incorrect geomezry they are too far outboard.
rocker arm witness mark on valve stem. incorrect geomezry they are too far outboard.
0 2020/01/17 11:32:08
witness mark of the roller on the valve stem. incorrect geometry - too far outboard
witness mark of the roller on the valve stem. incorrect geometry - too far outboard
0 2020/01/17 11:29:13
CompCams Magnum rocker arm
CompCams Magnum rocker arm
0 2020/01/17 11:23:53
clay says - plenty of room at 0,500" valve lift. so it will wven work with 1,62:1 rocker arms in case i needed more lift. ;)
clay says - plenty of room at 0,500" valve lift. so it will wven work with 1,62:1 rocker arms in case i needed more lift. ;)
0 2020/01/17 11:23:39
pushrods, turns out too short. finally i had to use a check-pushrod.
pushrods, turns out too short. finally i had to use a check-pushrod.
0 2020/01/17 11:21:35
lifter
lifter
0 2020/01/17 11:20:11
0 2020/01/17 11:18:27
0 2020/01/17 11:18:14
fixed lifter to check
fixed lifter to check
0 2020/01/17 11:15:37
a lot of room, nice at 0,500" valve lift. 1.62:1 rockers will definitively work
a lot of room, nice at 0,500" valve lift. 1.62:1 rockers will definitively work
0 2020/01/17 11:10:49
screw in studs
screw in studs
0 2020/01/17 11:10:37
finished block, only thing left is hone to spec for the new pistons. no boring at this time. pistons are 0,002" over. less machining and i want all the wall strength if it comes to my mind to add a turbo or compressor.
finished block, only thing left is hone to spec for the new pistons. no boring at this time. pistons are 0,002" over. less machining and i want all the wall strength if it comes to my mind to add a turbo or compressor.
0 2020/01/17 11:10:24
valves with check springs
valves with check springs
0 2020/01/17 11:05:57
clay method to check valve to piston clearance
clay method to check valve to piston clearance
0 2020/01/17 11:05:44
#1 at TODC
#1 at TODC
0 2020/01/17 11:05:29
the drive for the balance shaft
the drive for the balance shaft
0 2020/01/17 11:05:15
CompCams bumpstick
CompCams bumpstick
0 2020/01/17 11:05:05
the fixed lifter
the fixed lifter
0 2020/01/17 11:04:52
chain drive, nothing fancy
chain drive, nothing fancy
0 2020/01/17 11:04:37
camshaft retainer plate
camshaft retainer plate
0 2020/01/17 11:04:26
the screw in studs. bosses are still high. once geometry is checked we will cut them down.
the screw in studs. bosses are still high. once geometry is checked we will cut them down.
0 2020/01/17 11:04:14
© 2021 MH Sub I, LLC dba Internet Brands