99 4 door blazer
#513
Nice start on the tat! I got 3 hours in on my sleeve a week ago and I’ve got another 4 hour session scheduled for the 30th then it should be one more 3-4 hour session after that and it should be complete! The wife scheduled a full day 8 hour marathon session on 1/22 to start her full back piece and I must say I do not envy her having to sit for that one lol!
#514
Oh man... I can't imagine sitting for 8 hrs! I gotta get my old tatts touched up now that I got this one lol... they are all black, but years old and faded lol... not looking to get my Phoenix done, it take up most of my back and it'll be a couple hours of pounding lol.
On a blazer note:
I have all the parts now for the front end rebuild and rear axle swap. Mecahinc says he should be able to get the axles rebuilt this week, so truck might be off the road next week for the swap and rebuild lol, depending on his schedule lol... should only be about 8-9hrs work swapping everything in. Bolts have been worked on in the last few years so they shouldn't be seized too bad lol
Here are the shocks going in, I got upgraded rears for towing with coil overs, so will let you guys know how those work out.
On a blazer note:
I have all the parts now for the front end rebuild and rear axle swap. Mecahinc says he should be able to get the axles rebuilt this week, so truck might be off the road next week for the swap and rebuild lol, depending on his schedule lol... should only be about 8-9hrs work swapping everything in. Bolts have been worked on in the last few years so they shouldn't be seized too bad lol
Here are the shocks going in, I got upgraded rears for towing with coil overs, so will let you guys know how those work out.
#515
Getting some time into the bay this weekend, hoping to get the parts swapped out on the blazer.
Also installed by bday gift from the wife to myself lol, well half of it... there's still two pod leds to install. Gotta get wire and extend the wire harness that came with it, I want to mount them on the basket.
Night time light
Night time with led bar
Night time with high beems and led bar
Also installed by bday gift from the wife to myself lol, well half of it... there's still two pod leds to install. Gotta get wire and extend the wire harness that came with it, I want to mount them on the basket.
Night time light
Night time with led bar
Night time with high beems and led bar
#517
I was driving to work, and I gotta say I lit about a good 500km... clear morning time...
Just pulled over in a parking lot to do a test of the three close range and a dim lit area...
Night time running light
Night time plus high beams
Night time, high beams and light bar
Edit:
Took some pics on a none lit road:
Nights
Nights/high beams
Nights/highs and bar
Just pulled over in a parking lot to do a test of the three close range and a dim lit area...
Night time running light
Night time plus high beams
Night time, high beams and light bar
Edit:
Took some pics on a none lit road:
Nights
Nights/high beams
Nights/highs and bar
Last edited by DonL; 12-19-2020 at 09:16 AM.
#518
So rebuilding the front end.... again.... and well lone behold... I got screwed over by rough country again.... the so called proper upper control arms are no damn different then the original ones I got and the damn 6540 balljoint don't fit again...
I'm don't with this lift kit. Wasnt worth the cost of the lift, wasn't worth the headaches, wasn't worth the lifetime of the product....
I'm gonna figure out how to get the blazer out of the mechanics bay, then decide what to do...
I'm don't with this lift kit. Wasnt worth the cost of the lift, wasn't worth the headaches, wasn't worth the lifetime of the product....
I'm gonna figure out how to get the blazer out of the mechanics bay, then decide what to do...
#520
When I ordered these control arms, I call rough country in Texas. They were able to send a sent to a distributor about an hour away from me. I was told these where the right ones. I'm going to drive there tomorrow with the product and see what can be done.
my next option at this point is to scrap the rough country arms, buy stock arms, and find someone or somewhere to get ball joint spacers. I haven't even started looking at that option, and I'm scared to see how hard they are to find, if I can even find them...
my next option at this point is to scrap the rough country arms, buy stock arms, and find someone or somewhere to get ball joint spacers. I haven't even started looking at that option, and I'm scared to see how hard they are to find, if I can even find them...